اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThe PoGOLite control system and software
112
0
0.0
(
0
)
تأليف
M. S. Jackson
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The autonomous control system of PoGOLite is presented. PoGOLite is a balloon borne X-ray polarimeter designed to observe point sources. To obtain scientific data with optimal efficiency, independent of the ground connection, the payload control system has been made autonomous in most functions. The overall system architecture and the interconnections between components, as well as the automation philosophy and software, are described. Results of performance tests are given.
قيم البحث
اقرأ أيضاً
The E and B Experiment (EBEX) was a long-duration balloon-borne instrument designed to measure the polarization of the cosmic microwave background (CMB) radiation. EBEX was the first balloon-borne instrument to implement a kilo-pixel array of transit
ion edge sensor (TES) bolometric detectors and the first CMB experiment to use the digital version of the frequency domain multiplexing system for readout of the TES array. The scan strategy relied on 40 s peak-to-peak constant velocity azimuthal scans. We discuss the unique demands on the design and operation of the payload that resulted from these new technologies and the scan strategy. We describe the solutions implemented including the development of a power system designed to provide a total of at least 2.3 kW, a cooling system to dissipate 590 W consumed by the detectors readout system, software to manage and handle the data of the kilo-pixel array, and specialized attitude reconstruction software. We present flight performance data showing faultless management of the TES array, adequate powering and cooling of the readout electronics, and constraint of attitude reconstruction errors such that the spurious B-modes they induced were less than 10% of CMB B-mode power spectrum with $r=0.05$.
We present the data acquisition and control software for the operation of the Mini-Extreme Universe Space Observatory (EUSO), a space-based fluorescence telescope for the observation of extensive air showers and atmospheric phenomena. This framework
has been extensively tested alongside the development of Mini-EUSO and was finalized ahead of the successful launch of the instrument to the ISS on August 22, 2019. The data acquisition, housekeeping, and subsystem control are achieved using custom-designed front-end electronics based on a Xilinx Zynq XC7Z030 chip interfaced with a PCIe/104 CPU module via the integrated Zynq processing system. The instrument control interface is handled using an object-oriented C++ design, which can be run both autonomously and interactively as required. Although developed for Mini-EUSO, the modular design of both the software and hardware can easily be scaled up to larger instrument designs and adapted to different subsystem and communication requirements. As such, this framework will also be used in the upgrade of the EUSO-TA instrument and potentially for the next EUSO-SPB2 NASA Balloon flight. The software and firmware presented are open source and released with detailed and integrated documentation.
The Australian Astronomical Observatorys TAIPAN instrument deploys 150 Starbug robots to position optical fibres to accuracies of 0.3 arcsec, on a 32 cm glass field plate on the focal plane of the 1.2 m UK-Schmidt telescope. This paper describes the
software system developed to control and monitor the Starbugs, with particular emphasis on the automated path-finding algorithms, and the metrology software which keeps track of the position and motion of individual Starbugs as they independently move in a crowded field. The software employs a tiered approach to find a collision-free path for every Starbug, from its current position to its target location. This consists of three path-finding stages of increasing complexity and computational cost. For each Starbug a path is attempted using a simple method. If unsuccessful, subsequently more complex (and expensive) methods are tried until a valid path is found or the target is flagged as unreachable.
SOXS (Son Of X-Shooter) is a new spectrograph for the ESO NTT telescope, currently in the final design phase. The main instrument goal is to allow the characterization of transient sources based on alerts. It will cover from near-infrared to visibl
e bands with a spectral resolution of $R sim 4500$ using two separate, wavelength-optimized spectrographs. A visible camera, primarily intended for target acquisition and secondary guiding, will also provide a scientific light imaging mode. In this paper we present the current status of the design of the SOXS instrument control software, which is in charge of controlling all instrument functions and detectors, coordinating the execution of exposures, and implementing all observation, calibration and maintenance procedures. Given the extensive experience of the SOXS consortium in the development of instruments for the VLT, we decided to base the design of the Control System on the same standards, both for hardware and software control. We illustrate the control network, the instrument functions and detectors to be controlled, the overall design of SOXS Instrument Software (INS) and its main components. Then, we provide details about the control software for the most SOXS-specific features: control of the COTS-based imaging camera, the flexures compensation system and secondary guiding.
ASTRI (Astrofisica con Specchi a Tecnologia Replicante Italiana) is a Flagship Project financed by the Italian Ministry of Education, University and Research, and led by INAF, the Italian National Institute of Astrophysics. Main goals of the ASTRI pr
oject are the realization of an end-to-end prototype of a Small Size Telescope (SST) for the Cherenkov Telescope Array (CTA) in a dual-mirror configuration (SST-2M) and, subsequently, of a mini-array composed of a few SST-2M telescopes to be placed at the final CTA Southern Site. Here we present the main features of the Mini-Array Software System (MASS) that has a central role in the success of the ASTRI Project and will also serve as a prototype for the CTA software system. The MASS will provide a set of tools to prepare an observing proposal, to perform the observations specified therein (monitoring and controlling all the hardware components of each telescope), to analyze the acquired data online and to store/retrieve all the data products to/from the archive.}
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
