اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEnhanced coupling design of a detuned damped structure for clic
56
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The key feature of the improved coupling design in the Damped Detuned Structure (DDS) is focused on the four manifolds. Rectangular geometry slots and rectangular manifolds are used. This results in a significantly stronger coupling to the manifolds compared to the previous design. We describe the new design together with its wakefield damping properties.
قيم البحث
اقرأ أيضاً
A damped detuned structure for the main X-band linacs of CLIC is being investigated as an alternative design to the present baseline heavily damped structure. In our earlier designs we studied detuned structures, operating at 11.994 GHz, with a range
of dipole bandwidths in order to ensure the structure satisfies beam dynamics and rf breakdown constraints. Here we report on the development of a damped and detuned structure which satisfies both constraints. Preparations for high power testing of the structure are also discussed
As a joint effort in the JLC/NLC research program, we have developed a new type of damped detuned accelerator structure with optimized round-shaped cavities (RDDS). This paper discusses some important R&D aspects of the first structure in this series
(RDDS1). The design aspects covered are the cell design with sub-MHz precision, HOM detuning, coupling and damping technique and wakefield simulation. The fabrication issues covered are ultra-precision cell machining with micron accuracy, assembly and diffusion bonding technologies to satisfactorily meet bookshelf, straightness and cell rotational alignment requirements. The measurements described are the RF properties of single cavities and complete accelerator section, as well as wakefields from the ASSET tests at SLAC. Finally, future improvements are also discussed.
There are several background sources which may affect the analysis of data and detector performans at the CLIC project. One of the important background source is halo muons, which are generated along the beam delivery system (BDS), for the detector p
erformance. In order to reduce muon background, magnetized muon sweepers have been used as a shielding material that is already described in a previous study for CLIC [1]. The realistic muon sweeper has been designed with OPERA. The design parameters of muon sweeper have also been used to estimate muon background reduction with BDSIM Monte Carlo simulation code [2, 3].
This paper outlines the RF design of the CLIC (Compact Linear Collider) 30 GHz main linac accelerating structure and gives the resulting longitudinal and transverse mode properties. The critical requirement for multibunch operation, that transverse w
akefields be suppressed by two orders of magnitude within 0.7 ns (twenty fundamental mode cycles), has been demonstrated in a recent ASSET experiment. The feasibility of operating the structure at an accelerating gradient of 150 MV/m for 130 ns has yet to be demonstrated. Damage of the internal copper surfaces due to high electric fields or resulting from metal fatigue induced by cyclic surface heating effects are a major concern requiring further study.
Superconducting cavities with low RF frequencies and heavy damping of higher order modes (HOM) are desired for the main accelerator of High Energy Photon Source (HEPS), a 6 GeV synchrotron light source promising ultralow emittance currently under con
struction in Beijing. A compact 166.6 MHz superconducting cavity was proposed adopting a quarter-wave beta=1 geometry. Based on the successful development of a proof-of-principle cavity, a HOM-damped 166.6 MHz compact superconducting cavity was subsequently designed. A ferrite damper was installed on the beam pipe to reduce HOM impedance below the stringent threshold of coupled-bunch instabilities. Being compact, RF field heating on the cavity vacuum seal was carefully examined against quenching the NbTi flange. The cavity was later dressed with a helium vessel and the tuning mechanism was also realized. Excellent RF and mechanical properties were eventually achieved. Finally, the two-cavity string was designed to ensure smooth transitions among components and proper shielding of synchrotron light. This paper presents a complete design of a fully dressed HOM-damped low-frequency beta=1 superconducting cavity for HEPS.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
