اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEfficient numerical method of the fiber Bragg grating synthesis
67
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
A new numerical method is developed for solution of the Gelfand - Levitan - Marchenko inverse scattering integral equations. The method is based on the fast inversion procedure of a Toeplitz Hermitian matrix and special bordering technique. The method is highly competitive with the known discrete layer peeling method in speed and exceeds it noticeably in accuracy at high reflectance.
قيم البحث
اقرأ أيضاً
The unique spectral behavior exhibited by a class of non-uniform Bragg periodic structures, namely chirped and apodized fiber Bragg gratings (FBGs) influenced by parity and time reversal ($mathcal{PT}$) symmetry, is presented. The interplay between t
he $mathcal{PT}$-symmetry and nonuniformities brings exceptional functionalities in the broken $mathcal{PT}$-symmetric phase such as wavelength selective amplification and single-mode lasing for a wide range of variations in gain-loss. We observe that the device is no more passive and it undergoes a series of transitions from asymmetric reflection to unidirectional invisibility and multi-mode amplification as a consequence of variation in the imaginary part of the strength of modulation in different apodization profiles, namely Gaussian and raised cosine, at the given value of chirping. The chirping affords bandwidth control as well as control over the magnitude of the reflected (transmitted) light. Likewise, apodization offers additional functionality in the form of suppression of uncontrolled lasing behavior in the broken $mathcal{PT}$-symmetric regime besides moderating the reflected signals outside the band edges of the spectra.
We present a novel application of Fiber Bragg Grating (FBG) sensors in the construction and characterisation of Micro Pattern Gaseous Detector (MPGD), with particular attention to the realisation of the largest triple (Gas electron Multiplier) GEM ch
ambers so far operated, the GE1/1 chambers of the CMS experiment at LHC. The GE1/1 CMS project consists of 144 GEM chambers of about 0.5 m2 active area each, employing three GEM foils per chamber, to be installed in the forward region of the CMS endcap during the long shutdown of LHC in 2108-2019. The large active area of each GE1/1 chamber consists of GEM foils that are mechanically stretched in order to secure their flatness and the consequent uniform performance of the GE1/1 chamber across its whole active surface. So far FBGs have been used in high energy physics mainly as high precision positioning and re-positioning sensors and as low cost, easy to mount, low space consuming temperature sensors. FBGs are also commonly used for very precise strain measurements in material studies. In this work we present a novel use of FBGs as flatness and mechanical tensioning sensors applied to the wide GEM foils of the GE1/1 chambers. A network of FBG sensors have been used to determine the optimal mechanical tension applied and to characterise the mechanical tension that should be applied to the foils. We discuss the results of the test done on a full-sized GE1/1 final prototype, the studies done to fully characterise the GEM material, how this information was used to define a standard assembly procedure and possible future developments.
An analytic solution for Bragg grating with linear chirp in the form of confluent hypergeometric functions is analyzed in the asymptotic limit of long grating. Simple formulas for reflection coefficient and group delay are derived. The simplification
makes it possible to analyze irregularities of the curves and suggest the ways of their suppression. It is shown that the increase in chirp at fixed other parameters decreases the oscillations in the group delay, but gains the oscillations in the reflection spectrum. The conclusions are in agreement with numerical calculations.
Femtosecond laser writing is applied to form Bragg grating waveguides in the diamond bulk. Type II waveguides are integrated with a single pulse point-by-point periodic laser modification positioned towards the edge of the waveguide core. These photo
nic devices, operating in the telecommunications band, allow for simultaneous optical waveguiding and narrowband reflection from a 4th order grating. This fabrication technology opens the way towards advanced 3D photonic networks in diamond for a range of applications.
A novel approach which uses Fibre Bragg Grating (FBG) sensors has been utilised to assess and monitor the flatness of Gaseous Electron Multipliers (GEM) foils. The setup layout and preliminary results are presented.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
