اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدFabrication and Tolerance Issues and their Influence on Multi-Bunch Bbu and Emittance Dilution in the Construction of X-Band RDDS Linacs for the NLC
48
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The main linacs of the Next Linear Collider (NLC) will contain several thousand X-band RDDS (Rounded Damped Detuned Structures). The transverse wakefield in the structures is reduced by detuning the modal frequencies such that they destructively interfere and by four damping manifolds per structure which provide weak damping. Errors in the fabrication of the individual cells and in the alignment of the cells will reduce the cancellation of the modes. Here, we calculate the tolerances on random errors in the synchronous frequencies of the cells and the cell-to-cell alignment.
قيم البحث
اقرأ أيضاً
Earlier RDDS (Rounded Damped Detuned Structures) [1,2], designed, fabricated and tested at SLAC, in collaboration with KEK, have been shown to damp wakefields successfully. However, electrical breakdown has been found to occur in these structures and
this makes them inoperable at the desired gradient. Recent results [3] indicate that lowering the group velocity of the accelerating mode reduces electrical breakdown events. In order to preserve the filling time of each structure a high synchronous phase advance (150 degrees as opposed to 120 used in previous NLC designs) has been chosen. Here, damping of the wakefield is analyzed. Manifold damping and interleaving of structure cell frequencies is discussed. These wakefields impose alignment tolerances on the cells and on the structure as a whole. Tolerance calculations are performed and these are compared with analytic estimations.
Recent experiments at SLAC [1,2] and CERN [3] have revealed evidence of significant deformation in the form of pitting of the cells of the 1.8m series of structures DDS/RDDS (Damped Detuned Structure/Rounded Damped Detuned Structure). This pitting oc
curs in the high group velocity (vg /c = 0.012) end of the accelerating structure and little evidence of breakdown has been found in the lower group velocity end of the structure. Additional, albeit preliminary experimental evidence, suggests that shorter and lower group velocity structures have reduced breakdown events with increasing accelerating field strengths. Two designs are presented here, firstly a 90cm structure consisting of 83 cells with an initial vg/c = 0.0506 (known as H90VG5) and secondly, an even shorter structure of length 60cm consisting of 55 cells with an initial vg /c = 0.03 (known as H60VG3). The feasibility of using these structures to accelerate a charged beam over 10km is investigated. The particular issue focussed upon is suppression of the dipole wakefields via detuning of the cell frequencies and by locally damping individual cells in order to avoid BBU (Beam Break Up). Results are presented on beam-induced dipole wakefields and on the beam dynamics encountered on tracking the progress of the beam through several thousand accelerating structures. [1] C. Adolphsen, ROAA003, this conf. [2] R.H. Miller et al, FPAH062, this conf. [3] L. Groening et al, MPPH039, this conf
High brightness linear accelerators typically produce electron beams with peaks in the head and/or tail of the current profile. These current horns are formed after bunch compression due to non-linear correlations in the longitudinal phase space and
the higher order optics of the compressor. It has been suggested that this higher order compression can be corrected by inserting an octupole magnet near the center of a bunch compressor. However, this scheme provides a correlated transverse kick leading to growth of the projected emittance. We present here a method whereby octupole magnets are inserted into two sequential bunch compressors. By tuning a $pi$ betatron phase advance between the two octupoles, the correlated transverse kick from the first octupole can be corrected by the second, while providing a cummulative adjustment of the higher order compression.
Two standing-wave single-cell choke-mode damped structures with different choke dimensions which worked at 11.424 GHz were designed, manufactured and tuned by accelerator group in Tsinghua University. High power test was carried out to study choke-mo
de structures properties in high gradient and related breakdown phenomenon. A single-cell structure without choke which almost has the same inner dimension as choke-mode structure was also tested as a comparison to study how the choke affects high-gradient properties. In this paper, we report on the latest status of the high power test, including various observations and the experimental results.
The existence of a characteristic coherence length in FEL SASE Physics determines the independent lasing of different portions, namely the slices, of the electron bunch. Each slice may be characterized by different phase space properties (not necessa
rily equal emittances and Twiss coefficients). This fact opens new questions on the concept of beam matching and how the various portions of the beam contribute to the performances of the output radiation, including those associated with the transverse coherence.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
