اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدInductive-Adder Kicker Modulator for Darht-2
56
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
An all solid-state kicker modulator for the Dual-Axis Radiographic Hydrodynamic Test facility (DARHT-2) has been designed and tested. This kicker modulator uses multiple solid-state modules stacked in an inductive-adder configuration where the energy is switched into each section of the adder by a parallel array of MOSFETs. The modulator features very fast rise and fall times, pulse width agility and a high pulse-repetition rate in burst mode. The modulator can drive a 50* cable with voltages up to 20 kV and can be easily configured for either positive or negative polarity. The presentation will include test data collected from both the ETA II accelerator kicker and resistive dummy loads.
قيم البحث
اقرأ أيضاً
Fermilab Main Injector has been operating at high Beam Power levels since 2008 when multi-batch slip stacking became operational. In order to maintain and increase the beam power levels the localized beam loss due to beam left over in the injection k
icker gap during slip stacking needs to be addressed. A set of gap clearing kickers that kick any beam left in the injection gap to the beam abort have been built. The kickers were installed in the summer of 2009 and became operational in November of 2010. The kicker performance and its effect on the beam losses will be described.
We detail the calibration of the D-dot probes used on the Los Alamos National Laboratory DARHT Axis 1 LIA compensation cans (CCs). We hope this will serve not only as a record of this calibration, but also as a guide on how to perform similar calibra
tions on other systems where D-dots are deployed. Although a simple measurement, its difficulty lies in the fact that the same geometry used when fielded must be used during calibration, the ultimate goal being to measure the capacitance between the probe sensor and the component whose voltage one intends to measure. Because of its linearity with voltage, this can be done at a lower voltage than during fielding, the only caveat being that this lower voltage pulse must still provide enough signal to noise. After a brief summary of our results, we include a description of a compensation can, the D-dot probe and its operation. We then provide 3D simulation results of the capacitance of this probe to the high voltage bushing under test inside of the compensation can. Finally, we describe our calibration setup and discuss our results.
A double kicker system which extracts the ultra-low emittance multi-bunch beam stably from ATF damping ring was developed. The performance of the system was studied comparing an orbit jitter with single kicker extraction in single bunch mode. The pos
ition jitter reduction was estimated from the analysis of the extraction orbits. The reduction was confirmed for the double kicker system within a resolution of BPMs. More precise tuning of the system with a wire scanner has been tried by changing a beta function at the second kicker to get more reduction of kick angle jitter. The results of these studies are described in detail.
Each stage of an accelerator system has a limited dynamic range and therefore a chain of stages is required to reach high energy. A combination of septa and kicker magnets is frequently used to inject and extract beam from each stage. The kicker magn
ets typically produce rectangular field pulses with fast rise- and/or fall-times, however, the field strength is relatively low. To compensate for their relatively low field strength, the kicker magnets are generally combined with electromagnetic septa. The septa provide relatively strong field strength but are either DC or slow pulsed. This paper discusses injection and extraction systems with particular emphasis on the hardware required for the kicker magnet.
Fast kicker magnets are used to inject beam into and eject beam out of the CERN accelerator rings. These kickers are generally transmission line type magnets with a rectangular shaped aperture through which the beam passes. Unless special precautions
are taken the impedance of the yoke can provoke significant beam induced heating, especially for high intensities. In addition the impedance may contribute to beam instabilities. The results of longitudinal and transverse impedance measurements, for various kicker magnets, are presented and compared with analytical calculations: in addition predictions from a numerical analysis are discussed.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
