اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدData compression on board the PLANCK Satellite Low Frequency Instrument: optimal compression rate
74
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Data on board the future PLANCK Low Frequency Instrument (LFI), to measure the Cosmic Microwave Background (CMB) anisotropies, consist of $N$ differential temperature measurements, expanding a range of values we shall call $R$. Preliminary studies and telemetry allocation indicate the need of compressing these data by a ratio of $c_r simgt 10$. Here we present a study of entropy for (correlated multi-Gaussian discrete) noise, showing how the optimal compression $c_{r,opt}$, for a linearly discretized data set with $N_{bits}=log_2{N_{max}}$ bits is given by: $c_r simeq {N_{bits}/log_2(sqrt{2pi e} ~sigma_e/Delta)}$, where $sigma_eequiv (det C)^{1/2N}$ is some effective noise rms given by the covariance matrix $C$ and $Delta equiv R / N_{max}$ is the digital resolution. This $Delta$ only needs to be as small as the instrumental white noise RMS: $Delta simeq sigma_T simeq 2 mK$ (the nominal $mu K$ pixel sensitivity will only be achieved after averaging). Within the currently proposed $N_{bits}=16$ representation, a linear analogue to digital converter (ADC) will allow the digital storage of a large dynamic range of differential temperature $R= N_{max} Delta $ accounting for possible instrument drifts and instabilities (which could be reduced by proper on-board calibration). A well calibrated signal will be dominated by thermal (white) noise in the instrument: $sigma_e simeq sigma_T$, which could yield large compression rates $c_{r,opt} simeq 8$. This is the maximum lossless compression possible. In practice, point sources and $1/f$ noise will produce $sigma_e > sigma_T$ and $c_{r,opt} < 8$. This strategy seems safer than non-linear ADC or data reduction schemes (which could also be used at some stage).
قيم البحث
اقرأ أيضاً
We present a simple way of coding and compressing the data on board the Planck instruments (HFI and LFI) to address the problem of the on board data reduction. This is a critical issue in the Planck mission. The total information that can be download
ed to Earth is severely limited by the telemetry allocation. This limitation could reduce the amount of diagnostics sent on the stability of the radiometers and, as a consequence, curb the final sensitivity of the CMB anisotropy maps. Our proposal to address this problem consists in taking differences of consecutive circles at a given sky pointing. To a good approximation, these differences are independent of the external signal, and are dominated by thermal (white) instrumental noise. Using simulations and analytical predictions we show that high compression rates, $c_r simeq 10$, can be obtained with minor or zero loss of CMB sensitivity. Possible effects of digital distortion are also analized. The proposed scheme allows for flexibility to optimize the relation with other critical aspects of the mission. Thus, this study constitutes an important step towards a more realistic modeling of the final sensitivity of the CMB temperature anisotropy maps.
We describe the processing of data from the Low Frequency Instrument (LFI) used in production of the Planck Early Release Compact Source Catalogue (ERCSC). In particular, we discuss the steps involved in reducing the data from telemetry packets to cl
eaned, calibrated, time-ordered data (TOD) and frequency maps. Data are continuously calibrated using the modulation of the temperature of the cosmic microwave background radiation induced by the motion of the spacecraft. Noise properties are estimated from TOD from which the sky signal has been removed using a generalized least square map-making algorithm. Measured 1/f noise knee-frequencies range from 100mHz at 30GHz to a few tens of mHz at 70GHz. A destriping code (Madam) is employed to combine radiometric data and pointing information into sky maps, minimizing the variance of correlated noise. Noise covariance matrices required to compute statistical uncertainties on LFI and Planck products are also produced. Main beams are estimated down to the approx -10dB level using Jupiter transits, which are also used for geometrical calibration of the focal plane.
We describe the data processing pipeline of the Planck Low Frequency Instrument (LFI) data processing centre (DPC) to create and characterize full-sky maps based on the first 15.5 months of operations at 30, 44 and 70 GHz. In particular, we discuss t
he various steps involved in reducing the data, starting from telemetry packets through to the production of cleaned, calibrated timelines and calibrated frequency maps. Data are continuously calibrated using the modulation induced on the mean temperature of the cosmic microwave background radiation by the proper motion of the spacecraft. Sky signals other than the dipole are removed by an iterative procedure based on simultaneous fitting of calibration parameters and sky maps. Noise properties are estimated from time-ordered data after the sky signal has been removed, using a generalized least square map-making algorithm. A destriping code (Madam) is employed to combine radiometric data and pointing information into sky maps, minimizing the variance of correlated noise. Noise covariance matrices, required to compute statistical uncertainties on LFI and Planck products, are also produced. Main beams are estimated down to the -20 dB level using Jupiter transits, which are also used for the geometrical calibration of the focal plane.
We present an updated description of the Planck Low Frequency Instrument (LFI) data processing pipeline, associated with the 2015 data release. We point out the places where our results and methods have remained unchanged since the 2013 paper and we
highlight the changes made for the 2015 release, describing the products (especially timelines) and the ways in which they were obtained. We demonstrate that the pipeline is self-consistent (principally based on simulations) and report all null tests. For the first time, we present LFI maps in Stokes Q and U polarization. We refer to other related papers where more detailed descriptions of the LFI data processing pipeline may be found if needed.
We present a final description of the data-processing pipeline for the Planck, Low Frequency Instrument (LFI), implemented for the 2018 data release. Several improvements have been made with respect to the previous release, especially in the calibrat
ion process and in the correction of instrumental features such as the effects of nonlinearity in the response of the analogue-to-digital converters. We provide a brief pedagogical introduction to the complete pipeline, as well as a detailed description of the important changes implemented. Self-consistency of the pipeline is demonstrated using dedicated simulations and null tests. We present the final version of the LFI full sky maps at 30, 44, and 70 GHz, both in temperature and polarization, together with a refined estimate of the Solar dipole and a final assessment of the main LFI instrumental parameters.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
