اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدLaminar flow characterization using low-field magnetic resonance techniques
55
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Laminar flow velocity profiles depend heavily on fluid rheology. Developing methods of laminar flow characterization, based on low-field magnetic resonance (MR), contributes to the widespread industrial application of the MR technique in rheology. In this paper, we designed a low-cost, palm-sized permanent magnet with a 1H resonance frequency of 20.48 MHz to measure laminar flow. The magnet consists of two disk magnets, which were each tilted at an angle of 1{deg} from a starting separation of 1.4 cm to generate a constant gradient, 65 gauss/cm, in the direction of flow. Subsequently, a series of process methods, for MR measurements, were proposed to characterize Newtonian and non-Newtonian fluid flows in a pipe, including phase-based method, magnitude-based method, and velocity spectrum method. The accuracies of the proposed methods were validated by simulations, and experiments of Poiseuille flow and shear-thinning flow on the designed magnet. The new velocity profile methods proposed are advantageous because the MR instrumentation and measurement methods are simple and portable. The sophistication is found in the analysis although the physical principles are straight forward.
قيم البحث
اقرأ أيضاً
The impact of wall roughness on fully developed laminar pipe flow is investigated numerically. The roughness is comprised of square bars of varying size and pitch. Results show that the inverse relation between the friction factor and the Reynolds nu
mber in smooth pipes still persists in rough pipes, regardless of the rib height and pitch. At a given Reynolds number, the friction factor varies quadratically with roughness height and linearly with roughness pitch. We propose a single correlation for the friction factor that successfully collapses the data.
Efficiently predicting the flowfield and load in aerodynamic shape optimisation remains a highly challenging and relevant task. Deep learning methods have been of particular interest for such problems, due to their success for solving inverse problem
s in other fields. In the present study, U-net based deep neural network (DNN) models are trained with high-fidelity datasets to infer flow fields, and then employed as surrogate models to carry out the shape optimisation problem, i.e. to find a drag minimal profile with a fixed cross-section area subjected to a two-dimensional steady laminar flow. A level-set method as well as Bezier-curve method are used to parameterise the shape, while trained neural networks in conjunction with automatic differentiation are utilized to calculate the gradient flow in the optimisation framework. The optimised shapes and drag force values calculated from the flowfields predicted by DNN models agree well with reference data obtained via a Navier-Stokes solver and from the literature, which demonstrates that the DNN models are capable of predicting not only flowfield but also yield satisfactory aerodynamic forces. This is particularly promising as the DNNs were not specifically trained to infer aerodynamic forces. In conjunction with the fast runtime, the DNN-based optimisation framework shows promise for general aerodynamic design problems.
The movement of subaqueous sediment in laminar shearing flow is numerically investigated by the coupled lattice Boltzmann and discrete element methods. First, the numerical method is validated by comparing the phase diagram proposed by Ouriemi {it et
al.} ({it J. Fluid Mech}., vol. 636, 2009, pp. 321-336). Second, a detailed study on sediment movement is performed for sediment with varying solid volume fractions, and a nonlinear relationship between the normalised thickness of the mobile layer and the normalised fluid flow rate is observed for a densely-packed sediment. Third, an independent investigation on the effective viscosity and friction coefficient of the sediment under different fluid flow rates is conducted in a shear cell; and substitution of these two critical parameters into a theoretical expression proposed by Aussillous {it et al.} ({it J. Fluid Mech}., vol. 736, 2013, pp. 594-615) provides consistent predictions of bedload thickness with the simulation results of sediment movement. Therefore, we conclude that the non-Newtonian behaviour of densely-packed sediment leads to the nonlinear relationship between the normalised thickness of the mobile layer and the normalised fluid flow rate.
Numerical work on shockwave/boundary-layer interactions (SBLIs) to date has largely focused on span-periodic quasi-2D configurations that neglect the influence lateral confinement has on the core flow. The present study is concerned with the effect o
f flow confinement on Mach 2 laminar SBLI in rectangular ducts. An oblique shock generated by a 2 degree wedge forms a conical swept SBLI with sidewall boundary layers before reflecting from the bottom wall of the domain. Multiple large regions of flow-reversal are observed on the sidewalls, bottom wall and at the corner intersection. The main interaction is found to be strongly three-dimensional and highly dependent on the geometry of the duct. Comparison to quasi-2D span-periodic simulations showed sidewalls strengthen the interaction by 31% for the baseline configuration with an aspect ratio of one. The length of the shock generator and subsequent trailing edge expansion fan position was shown to be a critical parameter in determining the central separation length. By shortening the length of the shock generator, control of the interaction and suppression of the central interaction is demonstrated. Parametric studies of shock strength and duct aspect ratio were performed to find limiting behaviours. For the largest aspect ratio of four, three-dimensionality was visible across 30% of the span width away from the wall. Topological features of the three-dimensional separation are identified and shown to be consistent with `owl-like separations of the first kind. The reflection of the initial conical swept SBLIs is found to be the most significant factor determining the flow structures downstream of the main interaction.
Plane Couette flow presents a regular oblique turbulent-laminar pattern over a wide range of Reynolds numbers R between the globally stable base flow profile at low R<R_g and a uniformly turbulent regime at sufficiently large R>R_t. The numerical sim
ulations that we have performed on a pattern displaying a wavelength modulation show a relaxation of that modulation in agreement with what one would expect from a standard approach in terms of dissipative structures in extended geometry though the structuration develops on a turbulent background. Some consequences are discussed.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
