اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدOptimal Accelerated Degradation Testing Based on Bivariate Gamma Process with Dependent Components
53
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Accelerated degradation testing (ADT) is one of the major approaches in reliability engineering which allows accurate estimation of reliability characteristics of highly reliable systems within a relatively short time. The testing data are extrapolated through a physically reasonable statistical model to obtain estimates of lifetime quantiles at normal use conditions. The Gamma process is a natural model for degradation, which exhibits a monotone and strictly increasing degradation path. In this work, optimal experimental designs are derived for ADT with two response components. We consider the situations of independent as well as dependent marginal responses where the observational times are assumed to be fixed and known. The marginal degradation paths are assumed to follow a Gamma process where a copula function is utilized to express the dependence between both components. For the case of independent response components the optimal design minimizes the asymptotic variance of an estimated quantile of the failure time distribution at the normal use conditions. For the case of dependent response components the $D$-criterion is adopted to derive $D$-optimal designs. Further, $D$- and $c$-optimal designs are developed when the copula-based models are reduced to bivariate binary outcomes.
قيم البحث
اقرأ أيضاً
Accelerated degradation tests are used to provide accurate estimation of lifetime characteristics of highly reliable products within a relatively short testing time. Data from particular tests at high levels of stress (e.g., temperature, voltage, or
vibration) are extrapolated, through a physically meaningful statistical model, to attain estimates of lifetime quantiles at normal use conditions. The gamma process is a natural model for estimating the degradation increments over certain degradation paths, which exhibit a monotone and strictly increasing degradation pattern. In this work, we derive first an algorithm-based optimal design for a repeated measures degradation test with single failure mode that corresponds to a single response component. The univariate degradation process is expressed using a gamma model where a generalized linear model is introduced to facilitate the derivation of an optimal design. Consequently, we extend the univariate model and characterize optimal designs for accelerated degradation tests with bivariate degradation processes. The first bivariate model includes two gamma processes as marginal degradation models. The second bivariate models is expressed by a gamma process along with a mixed effects linear model. We derive optimal designs for minimizing the asymptotic variance for estimating some quantile of the failure time distribution at the normal use conditions. Sensitivity analysis is conducted to study the behavior of the resulting optimal designs under misspecifications of adopted nominal values.
Accelerated degradation tests are used to provide accurate estimation of lifetime properties of highly reliable products within a relatively short testing time. There data from particular tests at high levels of stress (e.,g. temperature, voltage, or
vibration) are extrapolated, through a physically meaningful model, to obtain estimates of lifetime quantiles under normal use conditions. In this work, we consider repeated measures accelerated degradation tests with multiple stress variables, where the degradation paths are assumed to follow a linear mixed effects model which is quite common in settings when repeated measures are made. We derive optimal experimental designs for minimizing the asymptotic variance for estimating the median failure time under normal use conditions when the time points for measurements are either fixed in advance or are also to be optimized.
In many real-life scenarios, system failure depends on dynamic stress-strength interference, where strength degrades and stress accumulates concurrently over time. In this paper, we consider the problem of finding an optimal replacement strategy that
balances the cost of replacement with the cost of failure and results in a minimum expected cost per unit time under cumulative damage model with strength degradation. The existing recommendations are applicable only under restricted distributional assumptions and/or with fixed strength. As theoretical evaluation of the expected cost per unit time turns out to be very complicated, a simulation-based algorithm is proposed to evaluate the expected cost rate and find the optimal replacement strategy. The proposed method is easy to implement having wider domain of application. For illustration, the proposed method is applied to real case studies on mailbox and cell-phone battery experiments.
Atmospheric trace-gas inversion is the procedure by which the sources and sinks of a trace gas are identified from observations of its mole fraction at isolated locations in space and time. This is inherently a spatio-temporal bivariate inversion pro
blem, since the mole-fraction field evolves in space and time and the flux is also spatio-temporally distributed. Further, the bivariate model is likely to be non-Gaussian since the flux field is rarely Gaussian. Here, we use conditioning to construct a non-Gaussian bivariate model, and we describe some of its properties through auto- and cross-cumulant functions. A bivariate non-Gaussian, specifically trans-Gaussian, model is then achieved through the use of Box--Cox transformations, and we facilitate Bayesian inference by approximating the likelihood in a hierarchical framework. Trace-gas inversion, especially at high spatial resolution, is frequently highly sensitive to prior specification. Therefore, unlike conventional approaches, we assimilate trace-gas inventory information with the observational data at the parameter layer, thus shifting prior sensitivity from the inventory itself to its spatial characteristics (e.g., its spatial length scale). We demonstrate the approach in controlled-experiment studies of methane inversion, using fluxes extracted from inventories of the UK and Ireland and of Northern Australia.
We extend the Approximate-Proximal Point (aProx) family of model-based methods for solving stochastic convex optimization problems, including stochastic subgradient, proximal point, and bundle methods, to the minibatch and accelerated setting. To do
so, we propose specific model-based algorithms and an acceleration scheme for which we provide non-asymptotic convergence guarantees, which are order-optimal in all problem-dependent constants and provide linear speedup in minibatch size, while maintaining the desirable robustness traits (e.g. to stepsize) of the aProx family. Additionally, we show improved convergence rates and matching lower bounds identifying new fundamental constants for interpolation problems, whose importance in statistical machine learning is growing; this, for example, gives a parallelization strategy for alternating projections. We corroborate our theoretical results with empirical testing to demonstrate the gains accurate modeling, acceleration, and minibatching provide.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
