اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدActive control of a diode laser with injection locking
132
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We present a simple and effective method to implement an active stabilization of a diode laser with injection locking, which requires minimal user intervenes. The injection locked state of the diode laser is probed by a photodetector, of which sensitivity is enhanced by a narrow laser-line filter. Taking advantage of the characteristic response of laser power to spectral modes from the narrow laser-line filter, we demonstrate that high spectral purity and low intensity noise of the diode can be simultaneously maintained by an active feedback to the injected laser. Our method is intrinsically cost-effective, and does not require bulky devices, such as Fabry-Perot interferometers or wavemeters, to actively stabilize the diode laser. Based on successful implementation of this method in our quantum gas experiments, it is conceivable that our active stabilization will greatly simplify potential applications of injection locking of diode lasers in modularized or integrated optical systems.
قيم البحث
اقرأ أيضاً
We study the injection locking bistability of a specially engineered two-color semiconductor Fabry-Perot laser. Oscillation in the uninjected primary mode leads to a bistability of single mode and two-color equilibria. With pulsed modulation of the i
njected power we demonstrate an all-optical memory element based on this bistability, where the uninjected primary mode is switched with 35 dB intensity contrast. Using experimental and theoretical analysis, we describe the associated bifurcation structure, which is not found in single mode systems with optical injection.
Ultra-low frequency noise lasers have been widely used in laser-based experiments. Most narrow-linewidth lasers are implemented by actively suppressing their frequency noise through a frequency noise servo loop (FNSL). The loop bandwidths (LBW) of FN
SLs are currently below megahertz, which is gradually tricky to meet application requirements, especially for wideband quantum sensing experiments. This article has experimentally implemented an FNSL with loop-delay-limited 3.5 MHz LBW, which is an order higher than the usual FNSLs. Using this FNSL, we achieved 70 dB laser frequency noise suppression over 100 kHz Fourier frequency range. This technology has broad applications in vast fields where wideband laser frequency noise suppression is inevitable.
The past decade has witnessed major advances in the development of microresonator-based frequency combs (microcombs) that are broadband optical frequency combs with repetition rates in the millimeter-wave to microwave domain. Integrated microcombs ca
n be manufactured using wafer-scale process and have been applied in numerous applications. Most of these advances are based on the harnessing of dissipative Kerr solitons (DKS) in optical microresonators with anomalous group velocity dispersion (GVD). However, microcombs can also be generated with normal GVD using dissipative localized structures that are referred to as dark pulse, switching wave or platicon. Importantly, as most materials feature intrinsic normal GVD, the requirement of dispersion engineering is significantly relaxed for platicon generation. Therefore while DKS microcombs require particular designs and fabrication processes, platicon microcombs can be readily built using standard CMOS-compatible platforms such as thin-film (i.e. typically below 300 nm) Si3N4. Yet laser self-injection locking that has been recently used to create highly compact integrated DKS microcomb modules has not been demonstrated for platicons. Here we report the first fully integrated platicon microcomb operating at a microwave-K-band repetition rate. Using laser self-injection locking of a DFB laser edge-coupled to a Si3N4 microresonator, platicons are electrically initiated and stably maintained, enabling a compact microcomb module without any complex control. We further characterize the phase noise of the platicon repetition rate and the pumping laser. The observation of self-injection-locked platicons facilitates future wide adoption of microcombs as a build-in block in standard photonic integrated architectures via commercial foundry service.
Injection locking is a well known and commonly used method for coherent light amplification. Usually injection locking is done with a single-frequency seeding beam. In this work we show that injection locking may also be achieved in the case of multi
-frequency seeding beam when slave laser provides sufficient frequency filtering. One relevant parameter turns out to be the frequency detuning between the free running slave laser and each injected frequency component. Stable selective locking to a set of three components separated of $1.2,$GHz is obtained for (positive) detuning values between zero and $1.5,$GHz depending on seeding power (ranging from 10 to 150 microwatt). This result suggests that, using distinct slave lasers for each line, a set of mutually coherent narrow-linewidth high-power radiation modes can be obtained.
Self-injection locking is a dynamic phenomenon representing stabilization of the emission frequency of an oscillator with a passive cavity enabling frequency filtered coherent feedback to the oscillator cavity. For instance, self-injection locking of
a semiconductor laser to a high-quality-factor (high-Q) whispering gallery mode (WGM) microresonator can result in multiple orders of magnitude reduction of the laser linewidth. The phenomenon was broadly studied in experiments, but its detailed theoretical model allowing improving the stabilization performance does not exist. In this paper we develop such a theory. We introduce five parameters identifying efficiency of the self-injection locking in an experiment, comprising back-scattering efficiency, phase delay between the laser and the high-Q cavities, frequency detuning between the laser and the high-Q cavities, the pump coupling efficiency, the optical path length between the laser and the microresonator. Our calculations show that the laser linewidth can be improved by two orders of magnitude compared with the case of not optimal self-injection locking. We present recommendations on the experimental realization of the optimal self-injection locking regime. The theoretical model provides deeper understanding of the self-injection locking and benefits multiple practical applications of self-injection locked oscillators.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
