اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCombined experimental/theoretical approach to residual stresses within multiplicative elasto-plasticity
79
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The study is devoted to geometrically non-linear modelling of viscoplastic structures with residual stresses. We advocate and develop a special approach to residual stresses based on the transition between reference configurations. The finite strain kinematics of the viscoplastic material is modelled by the multiplicative decomposition of the deformation gradient tensor. Numerical algorithms originally developed for unstressed materials are extended to materials with pre-stresses. Owing to the weak invariance of constitutive equations, the incorporation of pre-stresses happens without additional costs. Thus, the advocated approach is especially efficient. A novel experimental/theoretical method for assessment of residual stresses in welded structures is presented; the method combines advantages of purely experimental and theoretical approaches. To demonstrate the applicability of the proposed procedure, we simulate plate welding. As an example we show that the procedure allows to extrapolate the filed of residual stresses away from the measurement points. As another example, we address the reduction of weldment-related residual stresses by mechanical treatment.
قيم البحث
اقرأ أيضاً
The history dependence of the glasses formed from flow-melted steady states by a sudden cessation of the shear rate $dotgamma$ is studied in colloidal suspensions, by molecular dynamics simulations, and mode-coupling theory. In an ideal glass, stress
es relax only partially, leaving behind a finite persistent residual stress. For intermediate times, relaxation curves scale as a function of $dotgamma t$, even though no flow is present. The macroscopic stress evolution is connected to a length scale of residual liquefaction displayed by microscopic mean-squared displacements. The theory describes this history dependence of glasses sharing the same thermodynamic state variables, but differing static properties.
Ultraviolet-photoemission (UPS) measurements and supporting specific-heat, thermal-expansion, resistivity and magnetic-moment measurements are reported for the magnetic shape-memory alloy Ni$_2$MnGa over the temperature range $100K < T < 250K$. All m
easurements detect clear signatures of the premartensitic transition ($T_mathrm{PM}sim 247K$) and the martensitic transition ($T_mathrm{M} sim 196K$). Temperature-dependent UPS shows a dramatic depletion of states (pseudogap) at $T_mathrm{PM}$ located 0.3eV below the Fermi energy. First-principles electronic structure calculations show that the peak observed at 0.3eV in the UPS spectra for $T > T_mathrm{PM}$ is due to the Ni-d minority-spin electrons. Below $T_mathrm{M}$ this peak disappears, resulting in an enhanced density of states at energies around 0.8eV. This enhancement reflects Ni-d and Mn-d electronic contributions to the majority-spin density of states and is accompanied by significant reconstruction of the Fermi surface.
The incorporation of Eu into the diamond lattice is investigated in a combined theoretical-experimental study. The large size of the Eu ion induces a strain on the host lattice, which is minimal for the Eu-vacancy complex. The oxidation state of Eu i
s calculated to be 3+ for all defect models considered. In contrast, the total charge of the defect-complexes is shown to be negative -1.5 to -2.3 electron. Hybrid-functional electronic-band-structures show the luminescence of the Eu defect to be strongly dependent on the local defect geometry. The 4-coordinated Eu substitutional dopant is the most promising candidate to present the typical Eu3+ luminescence, while the 6-coordinated Eu-vacancy complex is expected not to present any luminescent behaviour. Preliminary experimental results on the treatment of diamond films with Eu-containing precursor indicate the possible incorporation of Eu into diamond films treated by drop-casting. Changes in the PL spectrum, with the main luminescent peak shifting from approximately 614 nm to 611 nm after the growth plasma exposure, and the appearance of a shoulder peak at 625 nm indicate the potential incorporation. Drop-casting treatment with an electronegative polymer material was shown not to be necessary to observe the Eu signature following the plasma exposure, and increased the background luminescence.
The effects of rhenium doping in the range 0 to 10 atomic percent on the static and dynamic magnetic properties of Fe65Co35 thin films have been studied experimentally as well as with first principles electronic structure calculations focusing on the
change of the saturation magnetization and the Gilbert damping parameter. Both experimental and theoretical results show that the saturation magnetization decreases with increasing Re doping level, while at the same time Gilbert damping parameter increases. The experimental low temperature saturation magnetic induction exhibits a 29 percent decrease, from 2.31 T to 1.64 T, in the investigated doping concentration range, which is more than predicted by the theoretical calculations. The room temperature value of the damping parameter obtained from ferromagnetic resonance measurements, correcting for extrinsic contributions to the damping, is for the undoped sample 0.0027, which is close to the theoretically calculated Gilbert damping parameter. With 10 atomic percent Re doping, the damping parameter increases to 0.0090, which is in good agreement with the theoretical value of 0.0073. The increase in damping parameter with Re doping is explained by the increase in density of states at Fermi level, mostly contributed by the spin-up channel of Re. Moreover, both experimental and theoretical values for the damping parameter are observed to be weakly decreasing with decreasing temperature.
The defect chemistry of perovskite compounds is directly related to the stoichiometry and to the valence states of the transition metal ions. Such relations are of high interest as they offer the possibility to influence the catalytic activity of per
ovskites for the application in solid-oxide fuel- and electrolyser cells. Combining theoretical and experimental approaches, we explore the feasibility of actively manipulating the valence state of Fe and the concentration of point defects by synthesizing non-stoichiometric LaFeO$_3$ (LFO). In the theoretical part, formation energies and concentrations of point defects were determined as a function of processing conditions by first-principles DFT+U calculations. Based on the DFT+U results, significant compositional deviations from stoichiometric LFO cannot be expected by providing rich or poor conditions of the oxidic precursor compounds (Fe$_2$O$_3$ and La$_2$O$_3$) in a solid-state processing route. In the experimental part, LFO was synthesized with a targeted La-site deficiency. We analyze the resulting phases in detail by X-ray diffraction and dedicated microscopy methods, namely scanning electron microscopy (SEM) and (scanning) transmission electron Microscopy ((S)TEM) in combination with energy dispersive X-ray spectroscopy (EDS) and electron energy-loss spectrometry (EELS). Instead of a variation of the La/Fe ratio, a mixture of two phases, Fe$_2$O$_3$/LaFeO$_3$, was observed resulting in an invariant charge state of Fe, which is in line with the theoretical results. We discuss our findings with respect to partly differing assumptions made in previously published studies on this material system.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
