اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدExploration of co-sputtered Ta$_2$O$_5$-ZrO$_2$ thin films for gravitational-wave detectors
144
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report on the development and extensive characterization of co-sputtered tantala-zirconia thin films, with the goal to decrease coating Brownian noise in present and future gravitational-wave detectors. We tested a variety of sputtering processes of different energies and deposition rates, and we considered the effect of different values of cation ratio $eta =$ Zr/(Zr+Ta) and of post-deposition heat treatment temperature $T_a$ on the optical and mechanical properties of the films. Co-sputtered zirconia proved to be an efficient way to frustrate crystallization in tantala thin films, allowing for a substantial increase of the maximum annealing temperature and hence for a decrease of coating mechanical loss. The lowest average coating loss was observed for an ion-beam sputtered sample with $eta = 0.485 pm 0.004$ annealed at 800 $^{circ}$C, yielding $overline{varphi} = 1.8 times 10^{-4}$. All coating samples showed cracks after annealing. Although in principle our measurements are sensitive to such defects, we found no evidence that our results were affected. The issue could be solved, at least for ion-beam sputtered coatings, by decreasing heating and cooling rates down to 7 $^{circ}$C/h. While we observed as little optical absorption as in the coatings of current gravitational-wave interferometers (0.5 parts per million), further development will be needed to decrease light scattering and avoid the formation of defects upon annealing.
قيم البحث
اقرأ أيضاً
Brownian thermal noise associated with highly-reflective mirror coatings is a fundamental limit for several precision experiments, including gravitational-wave detectors. Recently, there has been a worldwide effort to find mirror coatings with improv
ed thermal noise properties that also fulfill strict optical requirements such as low absorption and scatter. We report on the optical and mechanical properties of ion-beam-sputtered niobia and titania-niobia thin films, and we discuss application of such coatings in current and future gravitational-wave detectors. We also report an updated direct coating thermal noise measurement of the HR coatings used in Advanced LIGO and Advanced Virgo.
High finesse optical cavities of current interferometric gravitational-wave detectors are significantly limited in sensitivity by laser quantum noise and coating thermal noise. The thermal noise is associated with internal energy dissipation in the m
aterials that compose the test masses of the interferometer. Our understanding of how the internal friction is linked to the amorphous material structure is limited due to the complexity of the problem and the lack of studies that span over a large range of materials. We present a systematic investigation of amorphous metal oxide and Ta$_2$O$_5$-based mixed oxide coatings to evaluate their suitability for low Brownian noise experiments. It is shown that the mechanical loss of metal oxides is correlated to their amorphous morphology, with continuous random network materials such as SiO$_2$ and GeO$_2$ featuring the lowest loss angles. We evaluated different Ta$_2$O$_5$-based mixed oxide thin films and studied the influence of the dopant in the optical and elastic properties of the coating. We estimated the thermal noise associated with high-reflectance multilayer stacks that employ each of the mixed oxides as the high index material. We concluded that the current high index material of TiO$_2$-doped Ta$_2$O$_5$ is the optimal choice for reduced thermal noise among Ta$_2$O$_5$-based mixed oxide coatings with low dopant concentrations.
Amorphous oxide thin films play a fundamental role in state-of-the art interferometry experiments, such as gravitational wave detectors where these films compose the high reflectance mirrors of end and input masses. The sensitivity of these detectors
is affected by thermal noise in the mirrors with its main source being the mechanical loss of the high index layers. These thermally driven fluctuations are a fundamental limit to optical interferometry experiments and there is a pressing need to understand the underlying processes that lead to mechanical dissipation in materials at room temperature. Two strategies are known to lower the mechanical loss: employing a mixture of Ta$_2$O$_5$ with $approx$ 20% of TiO$_2$ and post-deposition annealing, but the reasons behind this are not completely understood. In this work, we present a systematic study of the structural and optical properties of ion beam sputtered TiO$_2$-doped Ta$_2$O$_5$ films as a function of the annealing temperature. We show for the first time that low mechanical loss is associated with a material morphology that consists of nanometer sized Ar-rich bubbles embedded into an atomically homogeneous mixed titanium-tantalum oxide. When the Ti cation ratio is high, however, phase separation occurs in the film which leads to increased mechanical loss. These results indicate that for designing low mechanical loss mixed oxide coatings for interferometry applications it would be beneficial to identify materials with the ability to form ternary compounds while the dopant ratio needs to be kept low to avoid phase separation.
We present a systematic study of the magnetic properties of semiconducting ZnFe$_2$O$_4$ thin films fabricated by pulsed laser deposition at low and high oxygen partial pressure and annealed in oxygen and argon atmosphere, respectively. The magnetic
response is enhanced by annealing the films at 250$^{circ}$C and diminished at annealing temperatures above 300$^{circ}$C. The initial increase is attributed to the formation of oxygen vacancies after argon treatment, evident by the increase in the low energy absorption at $sim$ 0.9 eV involving Fe$^{2+}$ cations. The weakened magnetic response is related to a decline in disorder with a cation redistribution toward a normal spinel configuration. The structural renormalization is consistent with the decrease and increase in oscillator strength of respective electronic transitions involving tetrahedrally (at $sim$ 3.5 eV) and octahedrally (at $sim$ 5.7 eV) coordinated Fe$^{3+}$ cations.
Modern ground-based gravitational wave (GW) detectors require a complex interferometer configuration with multiple coupled optical cavities. Since achieving the resonances of the arm cavities is the most challenging among the lock acquisition process
es, the scheme called arm length stabilization (ALS) had been employed for lock acquisition of the arm cavities. We designed a new type of the ALS, which is compatible with the interferometers having long arms like the next generation GW detectors. The features of the new ALS are that the control configuration is simpler than those of previous ones and that it is not necessary to lay optical fibers for the ALS along the kilometer-long arms of the detector. Along with simulations of its noise performance, an experimental test of the new ALS was performed utilizing a single arm cavity of KAGRA. This paper presents the first results of the test where we demonstrated that lock acquisition of the arm cavity was achieved using the new ALS and residual noise was measured to be $8.2,mathrm{Hz}$ in units of frequency, which is smaller than the linewidth of the arm cavity and thus low enough to lock the full interferometer of KAGRA in a repeatable and reliable manner.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
