اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدLow Radio Frequency Observations from the Moon Enabled by NASA Landed Payload Missions
138
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
A new era of exploration of the low radio frequency Universe from the Moon will soon be underway with landed payload missions facilitated by NASAs Commercial Lunar Payload Services (CLPS) program. CLPS landers are scheduled to deliver two radio science experiments, ROLSES to the nearside and LuSEE to the farside, beginning in 2021. These instruments would be pathfinders for a 10-km diameter interferometric array, FARSIDE, composed of 128 pairs of dipole antennas proposed to be delivered to the lunar surface later in the decade. ROLSES and LuSEE, operating at frequencies from 100 kHz to a few tens of MHz, will investigate the plasma environment above the lunar surface and measure the fidelity of radio spectra on the surface. Both use electrically-short, spiral-tube deployable antennas and radio spectrometers based upon previous flight models. ROLSES will measure the photoelectron sheath density to better understand the charging of the lunar surface via photoionization and impacts from the solar wind, charged dust, and current anthropogenic radio frequency interference. LuSEE will measure the local magnetic field and exo-ionospheric density, interplanetary radio bursts, Jovian and terrestrial natural radio emission, and the galactic synchrotron spectrum. FARSIDE, and its precursor risk-reduction six antenna-node array PRIME, would be the first radio interferometers on the Moon. FARSIDE would break new ground by imaging radio emission from Coronal Mass Ejections (CME) beyond 2 solar radii, monitor auroral radiation from the B-fields of Uranus and Neptune (not observed since Voyager), and detect radio emission from stellar CMEs and the magnetic fields of nearby potentially habitable exoplanets.
قيم البحث
اقرأ أيضاً
A new generation of low frequency radio telescopes is seeking to observe the redshifted 21 cm signal from the Epoch of Reionization (EoR), requiring innovative methods of calibration and imaging to overcome the difficulties of widefield low frequency
radio interferometry. Precise calibration will be required to separate the small expected EoR signal from the strong foreground emission at the frequencies of interest between 80 and 300 MHz. The Moon may be useful as a calibration source for detection of the EoR signature, as it should have a smooth and predictable thermal spectrum across the frequency band of interest. Initial observations of the Moon with the Murchison Widefield Array 32 tile prototype show that the Moon does exhibit a similar trend to that expected for a cool thermally emitting body in the observed frequency range, but that the spectrum is corrupted by reflected radio emission from Earth. In particular, there is an abrupt increase in the observed flux density of the Moon within the internationally recognised Frequency Modulated (FM) radio band. The observations have implications for future low frequency surveys and EoR detection experiments that will need to take this reflected emission from the Moon into account. The results also allow us to estimate the equivalent isotropic power emitted by the Earth in the FM band and to determine how bright the Earth might appear at metre wavelengths to an observer beyond our own solar system.
This paper describes the new QuickFind method in LcTools for finding signals and associated TTVs (Transit Timing Variations) in light curves from NASA space missions. QuickFind is adept at finding medium to large sized signals (generally those with S
/N ratios above 15) extremely fast, significantly reducing overall processing time for a light curve as compared to the BLS detection method. For example, on the lead authors computer, QuickFind was able to detect both KOI signals for star 10937029 in a 14 quarter Kepler light curve spanning 1,459 days in roughly 2 seconds whereas BLS took about 155 seconds to find both signals making QuickFind in this example about 77 times faster than BLS. This paper focuses on the user interfaces, data processing algorithm, and performance tests for the QuickFind method in LcTools.
Astrophysics spans an enormous range of questions on scales from individual planets to the entire cosmos. To address the richness of 21st century astrophysics requires a corresponding richness of telescopes spanning all bands and all messengers. Much
scientific benefit comes from having the multi-wavelength capability available at the same time. Most of these bands,or measurement sensitivities, require space-based missions. Historically, NASA has addressed this need for breadth with a small number of flagship-class missions and a larger number of Explorer missions. While the Explorer program continues to flourish, there is a large gap between Explorers and strategic missions. A fortunate combination of new astrophysics technologies with new, high capacity, low dollar-per-kg to orbit launchers, and new satellite buses allow for cheaper missions with capabilities approaching strategic mission levels. NASA has recognized these developments by calling for Probe-class mission ideas for mission studies, spanning most of the electromagnetic spectrum from GeV gamma-rays to the far infrared, and the new messengers of neutrinos and ultra-high energy cosmic rays. The key insight from the Probes exercise is that order-of-magnitude advances in science performance metrics are possible across the board for initial total cost estimates in the range 500M-1B dollars.
Since 2009, the Kepler, K2, and TESS missions have produced a vast number of lightcurves for public use. To assist citizen scientists in processing those lightcurves, the LcTools software system was developed. The system provides a set of tools to ef
ficiently search for signals of interest in large sets of lightcurves using automated and manual (visual) techniques. At the heart of the system is a multipurpose lightcurve viewer and signal processor with advanced navigation and display capabilities to facilitate the search for signals. Other applications in the system are available for building lightcurve files in bulk, finding periodic signals automatically, and generating signal reports. This paper describes each application in the system and the methods by which the software can be used to detect and record signals. The software is free and can be obtained from the lead author by request.
Low radio frequency experiments performed on Earth are contaminated by both ionospheric effects and radio frequency interference (RFI) from Earth-based sources. The lunar farside provides a unique environment above the ionosphere where RFI is heavily
attenuated by the presence of the Moon. We present electrodynamics simulations of the propagation of radio waves around and through the Moon in order to characterize the level of attenuation on the farside. The simulations are performed for a range of frequencies up to 100 kHz, assuming a spherical lunar shape with an average, constant density. Additionally, we investigate the role of the topography and density profile of the Moon in the propagation of radio waves and find only small effects on the intensity of RFI. Due to the computational demands of performing simulations at higher frequencies, we propose a model for extrapolating the width of the quiet region above 100 kHz that also takes into account height above the lunar surface as well as the intensity threshold chosen to define the quiet region. This model, which we make publicly available through a Python package, allows the size of the radio quiet region to be easily calculated both in orbit or on the surface, making it directly applicable for lunar satellites as well as surface missions.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
