اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدInfluence of surface structure and strain on indium segregation in InGaAs: a first-principles investigation
66
0
0.0
(
0
)
تأليف
Soumya S. Bhat
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The surface segregation of indium atoms in InGaAs is investigated using first-principles calculations based on density functional theory. Through the calculation of segregation energies for (100), (110), and (111) surfaces of GaAs we analyze the decisive role of surface orientation on indium segregation. Further, our calculations reveal that the variation of segregation energy as a function of applied strain strongly depends on surface reconstruction. Obtained segregation energy trends are discussed in light of atomic bonding probed via integrated crystal orbital Hamilton population. Results presented in this paper are anticipated to guide experimental efforts to achieve control on In segregation by managing As-flux along with the application of strain.
قيم البحث
اقرأ أيضاً
We have investigated InGaAs layers grown by molecular-beam epitaxy on GaAs(001) by transmission electron microscopy (TEM) and photoluminescence spectroscopy. InGaAs layers with In-concentrations of 16, 25 and 28 % and respective thicknesses of 20, 22
and 23 monolayers were deposited at 535 C. The parameters were chosen to grow layers slightly above and below the transition between the two- and three-dimensional growth mode. In-concentration profiles were obtained from high-resolution TEM images by composition evaluation by lattice fringe analysis. The measured profiles can be well described applying the segregation model of Muraki et al. [Appl. Phys. Lett. 61 (1992) 557]. Calculated photoluminescence peak positions on the basis of the measured concentration profiles are in good agreement with the experimental ones. Evaluating experimental In-concentration profiles it is found that the transition from the two-dimensional to the three-dimensional growth mode occurs if the indium content in the In-floating layer exceeds 1.1+/-0.2 monolayers. The measured exponential decrease of the In-concentration within the cap layer on top of the islands reveals that the In-floating layer is not consumed during island formation. The segregation efficiency above the islands is increased compared to the quantum wells which is explained tentatively by strain-dependent lattice-site selection of In. In addition, In0.25Ga0.75As quantum wells were grown at different temperatures between 500 oC and 550 oC. The evaluation of concentration profiles shows that the segregation efficiency increases from R=0.65 to R=0.83.
We present here a comprehensive search for the structure of the Si(553)-Au reconstruction. More than two hundred different trial structures have been studied using first-principles density-functional calculations with the SIESTA code. An iterative pr
ocedure, with a step-by-step increase of the accuracy and computational cost of the calculations, was used to allow for the study of this large number of configurations. We have considered reconstructions restricted to the topmost bilayer and studied two types: i) flat surface-bilayer models, where atoms at the topmost bilayer present different coordinations and registries with the underlying bulk, and ii) nine different models based on the substitution of a silicon atom by a gold atom in different positions of a $pi$-bonded chain reconstruction of the Si(553) surface. We have developed a compact notation that allows us to label and identify all these structures. This is very useful for the automatic generation of trial geometries and counting the number of inequivalent structures, i.e., structures having different bonding topologies. The most stable models are those that exhibit a honeycomb-chain structure at the step edge. One of our models (model f2) reproduces the main features of the room temperature photoemission and scanning-tunneling microscopy data. Thus we conclude that f2 structure is a good candidate for the high temperature structure of the Si(553)-Au surface.
Strain engineering is a very effective method to continuously tune the electronic, topological, optical and thermoelectric properties of materials. In this work, strain-dependent phonon transport of recently-fabricated antimonene (Sb monolayer) under
biaxial strain is investigated from a combination of first-principles calculations and the linearized phonon Boltzmann equation. It is found that the ZA dispersion of antimonene with strain less than -1% gives imaginary frequencies, which suggests that compressive strain can induce structural instability. Experimentally, it is possible to enhance structural stability by tensile strain. Calculated results show that lattice thermal conductivity increases with strain changing from -1% to 6%, and lattice thermal conductivity at 6% strain is 5.6 times larger than that at -1% strain at room temperature. It is interesting that lattice thermal conductivity is in inverse proportion to buckling parameter $h$ in considered strain range. Such a strain dependence of lattice thermal conductivity is attributed to enhanced phonon lifetimes caused by increased strain, while group velocities have a decreased effect on lattice thermal conductivity with increasing strain. It is found that acoustic branches dominate the lattice thermal conductivity over the full strain range. The cumulative room-temperature lattice thermal conductivity at -1% strain converges to maximum with phonon mean free path (MFP) at 50 nm, while one at 6% strain becomes as large as 44 $mathrm{mu m}$, which suggests that strain can give rise to very strong size effects on lattice thermal conductivity in antimonene. These results may provide guidance on fabrication techniques of antimonene, and offer perspectives on tuning lattice thermal conductivity by size and strain for applications of thermal management and thermoelectricity.
We use first principles density functional theory to investigate the softening of polar phonon modes in rutile TiO$_2$ under tensile (110)-oriented strain. We show that the system becomes unstable against a ferroelectric distortion with polarization
along (110) for experimentally accessible strain values. The resulting polarization, estimated from the Born effective charges, even exceeds the bulk polarization of BaTiO$_3$. Our calculations demonstrate the different strain dependence of polar modes polarized along (110) and (001) directions, and we discuss the possibility of strain engineering the polarization direction, and the resulting dielectric and piezoelectric response, in thin films of TiO$_2$ grown on suitable substrates.
Different stoichiometric configurations of graphane and graphene fluoride are investigated within density functional theory. Their structural and electronic properties are compared, and we indicate the similarities and differences among the various c
onfigurations. Large differences between graphane and graphene fluoride are found that are caused by the presence of charges on the fluorine atoms. A new configuration that is more stable than the boat configuration is predicted for graphene fluoride. We also perform GW calculations for the electronic band gap of both graphene derivatives. These band gaps and also the calculated Youngs moduli are at variance with available experimental data. This might indicate that the experimental samples contain a large number of defects or are only partially covered with H or F.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
