اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديد2.5-kV AlGaN/GaN Schottky Barrier Diode on Silicon Substrate with Recessed-anode Structure
85
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this letter, we demonstrate high-performance lateral AlGaN/GaN Schottky barrier diodes (SBD) on Si substrate with a recessed-anode structure. The optimized rapid etch process provides results in improving etching quality with a 0.26-nm roughness of the anode recessed surface. By using the high work function metal Pt as the Schottky electrode, a low Von of 0.71 V is obtained with a high uniformity of 0.023 V for 40 devices. Supported by the flat anode recess surface and related field plate design, the SBD device with the anode-cathode spacing of 15 um show the Ron,sp of 1.53 mOhm.cm2 only, the breakdown voltage can reach 1592 V with a high power FOM (Figure-of-Merit) of 1656 MW/cm2. For the SBD device with the anode-cathode spacing of 30 um, the breakdown voltage can be as high as 2521 V and the power FOM is 1244 MW/cm2.
قيم البحث
اقرأ أيضاً
GaN-based lateral Schottky diodes (SBDs) have attracted great attention for high-power applications due to its combined high electron mobility and large critical breakdown field. However, the breakdown voltage (BV) of the SBDs are far from exploiting
the material advantages of GaN at present, limiting the desire to use GaN for ultra-high voltage (UHV) applications. Then, a golden question is whether the excellent properties of GaN-based materials can be practically used in the UHV field? Here we demonstrate UHV AlGaN/GaN SBDs on sapphire with a BV of 10.6 kV, a specific on-resistance of 25.8 m{Omega}.cm2, yielding a power figure of merit of more than 3.8 GW/cm2. These devices are designed with single channel and 85-{mu}m anode-to-cathode spacing, without other additional electric field management, demonstrating its great potential for the UHV application in power electronics.
A comprehensive current-voltage (I-V) characterization is performed for three different Schottky contacts; Pt, Ni and Ti, to unintentionally doped (UID) {beta}-(Al0.19Ga0.81)2O3 grown by molecular beam epitaxy (MBE) on {beta}-Ga2O3 for temperatures r
anging between 25C -300C. Reciprocal space mapping shows the (Al0.19Ga0.81)2O3 films are strained and lattice matched to the substrate. Schottky Barrier Height (SBH), ideality factor (n), and series resistance (Rs) are extracted from the I-V characteristics for the three types of metals and temperatures. Room temperature capacitance-voltage (C-V) measurements revealed fully depleted {beta}-(Al0.19Ga0.81)2O3 layer. Extracted room temperature SBHs after zero field correction for Pt, Ni and Ti were 2.39 eV, 2.21 eV, and 1.22 eV respectively. Variation of SBHs with metal clearly indicates the dependence on work function.
Two-dimensional MoS2 has emerged as promising material for nanoelectronics and spintronics due to its exotic properties. However, high contact resistance at metal semiconductor MoS2 interface still remains an open issue. Here, we report electronic pr
operties of field effect transistor devices using monolayer MoS2 channels and permalloy (Py) as ferromagnetic (FM) metal contacts. Monolayer MoS2 channels were directly grown on SiO2/Si substrate via chemical vapor deposition technique. The increase in current with back gate voltage shows the tunability of FET characteristics. The Schottky barrier height (SBH) estimated for Py/MoS2 contacts is found to be +28.8 meV (zero-bias), which is the smallest value reported so-far for any direct metal (magnetic or non-magnetic)/monolayer MoS2 contact. With the application of gate voltage (+10 V), SBH shows a drastic reduction down to a value of -6.8 meV. The negative SBH reveals ohmic behavior of Py/MoS2 contacts. Low SBH with controlled ohmic nature of FM contacts is a primary requirement for MoS2 based spintronics and therefore using directly grown MoS2 channels in the present study can pave a path towards high performance devices for large scale applications.
Traditionally, Schottky diodes are used statically in the electronic information industry but dynamic state Schottky diodes based applications have been rarely explored. Herein, a novel Schottky diode named moving Schottky diode generator has been de
signed, which can convert mechanical energy into electrical energy with voltage output as high as 0.6V, by means of lateral movement between graphene/metal film and semiconductor, where the semiconductor can be non-piezoelectric materials. The mechanism is based on the built-in electric field separation of drifting electrons in moving van der Waals Schottky diode. The power output can be further increased in future through optimizing the Schottky diode. The graphene film/silicon moving van der Waals Schottky diode based generator behaves better stability. This direct-current generator has the potential of converting mechanical efficiently and vibrational energy into electricity and enables many promising applications.
In this paper, we describe the design and characterization of 400-nm-long (88 periods) AlxGa1-xN/AlN (0 < x < 0.1) quantum dot superlattices deposited on self-assembled GaN nanowires for application in electron-pumped ultraviolet sources. The optical
performance of GaN/AlN superlattices on nanowires is compared with the emission of planar GaN/AlN superlattices with the same periodicity and thickness grown on bulk GaN substrates along the N-polar and metal-polar crystallographic axes. The nanowire samples are less sensitive to nonradiative recombination than planar layers, attaining internal quantum efficiencies (IQE) in excess of 60% at room temperature even under low injection conditions. The IQE remains stable for higher excitation power densities, up to 50 kW/cm2. We demonstrate that the nanowire superlattice is long enough to collect the electron-hole pairs generated by an electron beam with an acceleration voltage VA = 5 kV. At such VA, the light emitted from the nanowire ensemble does not show any sign of quenching under constant electron beam excitation (tested for an excitation power density around 8 kW/cm2 over the scale of minutes). Varying the dot/barrier thickness ratio and the Al content in the dots, the nanowire peak emission can be tuned in the range from 340 to 258 nm. Keywords: GaN, AlN, nanowire, ultraviolet
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
