اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدSurface Crystallization of Monoatomic Pd Metallic Glasses
66
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Crystallization from an amorphous atomic structure is usually seen as a spontaneous process in pursuit of a lower energy state, but for alloy systems it is often hard to elucidate because of the intrinsic structural and compositional complexity. Here, by means of electron beam irradiation, we found surface-limited, and thus size-dependent crystallization in a system of monoatomic Pd metallic glass, which is ascribed to the structural differences between the surface and the interior. The equilibrium thickness of the surface crystallization is controllable, presenting a promising approach to fabricate novel nanostructures. The investigation is believed to provide a general understanding of solid amorphous-to-crystalline phase transition from the nanoscale to the bulk size.
قيم البحث
اقرأ أيضاً
Physically vitrifying single-element metallic glass requires ultrahigh cooling rates, which are still unachievable for most of the closest-packed metals. Here, we report a facile synthetic strategy for creating mono-atomic palladium metallic glass na
noparticles with a purity of 99.35 +/- 0.23 at% from palladium-silicon liquid droplets using a cooling rate below 1000 K/s. In-situ environmental transmission electron microscopy directly detected the leaching of silicon. Further hydrogen absorption experiment showed that this palladium metallic glass expanded little upon hydrogen uptake, exhibiting a great potential application for hydrogen separation. Our results provide insight into the formation of mono-atomic metallic glass at nanoscale.
The enhancement of surface diffusion (DS) over the bulk (DV) in metallic glasses (MGs) is well documented and likely to strongly influence the properties of glasses grown by vapor deposition. Here, we use classical molecular dynamics simulations to i
dentify different factors influencing the enhancement of surface diffusion in MGs. MGs have a simple atomic structure and belong to the category of moderately fragile glasses that undergo pronounced slowdown of bulk dynamics with cooling close to the glass transition temperature (Tg). We observe that DS exhibits a much more moderate slowdown compared to DV when approaching Tg, and DS/DV at Tg varies by two orders of magnitude among the MGs investigated. We demonstrate that both the surface energy and the fraction of missing bonds for surface atoms show good correlation to DS/DV, implying that the loss of nearest neighbors at the surface directly translates into higher mobility, unlike the behavior of network- and hydrogen-bonded organic glasses. Fragility, a measure of the slowdown of bulk dynamics close to Tg, also correlates to DS/DV, with more fragile systems having larger surface enhancement of mobility. The deviations observed in the fragility and DS over DV relationship are shown to be correlated to the extent of segregation or depletion of the mobile element at the surface. Finally, we explore the relationship between the diffusion pre-exponential factor (D0) and activation energy (Q) and compare to a ln(D0)-Q correlation previously established for bulk glasses, demonstrating similar correlations from MD as in the experiments and that the surface and bulk have very similar ln(D0)-Q correlations.
Metallic glasses are excellent candidates for biomedical implant applications due to their inherent strength and corrosion resistance. Use of metallic glasses in structural applications is limited, however, because bulk dimensions are challenging to
achieve. Glass-forming ability (GFA) varies strongly with alloy composition and becomes more difficult to predict as the number of chemical species in a system increases. Here we present a theoretical model - implemented in the AFLOW framework - for predicting GFA based on the competition between crystalline phases, and apply it to biologically relevant binary and ternary systems. Elastic properties are estimated based on the rule of mixtures for alloy systems that are predicted to be bulk glass-formers. Focusing on Ca- and Mg-based systems for use in biodegradable orthopedic support applications, we suggest alloys in the AgCaMg and AgMgZn families for further study; and alloys based on the compositions: Ag$_{0.33}$Mg$_{0.67}$, Cu$_{0.5}$Mg$_{0.5}$, Cu$_{0.37}$Mg$_{0.63}$ and Cu$_{0.25}$Mg$_{0.5}$Zn$_{0.25}$.
The bulk and surface dynamics of Cu50Zr50 metallic glass were studied using classical molecular dynamics (MD) simulations. As the alloy undergoes cooling, it passes through liquid, supercooled, and glassy states. While bulk dynamics showed a marked s
lowing down prior to glass formation, with increasing activation energy, the slowdown in surface dynamics was relatively subtle. The surface exhibited a lower glass transition temperature than the bulk, and the dynamics preceding the transition were accurately described by a temperature-independent activation energy. Surface dynamics were much faster than bulk at a given temperature in the supercooled state, but surface and bulk dynamics were found to be very similar when compared at their respective glass transition temperatures. The manifestation of dynamical heterogeneity, as characterized by the non-Gaussian parameter and breakdown of the Stokes-Einstein equation, was also similar between bulk and surface for temperatures scaled by their respective glass transition temperatures. Individual atom motion was dominated by a cage and jump mechanism in the glassy state for both the bulk and surface. We utilize this cage and jump mechanisms to separate the activation energy for diffusion into two parts: (i) cage-breaking barrier (Q1), associated with the rearrangement of neighboring atoms to free up space and (ii) the subsequent jump barrier (Q2). It was observed that Q1 dominates Q2 for both bulk and surface diffusion, and the difference in activation energies for bulk and surface diffusion mainly arose from the differences in cage-breaking barrier Q1.
Mechanical behaviors of bulk metallic glasses (BMGs) including heterogeneous and homogeneous deformation are interpreted by phenomenological shear transformation zones (STZs) model. Currently, information about STZs, i.e. size and density, is only ex
tracted by fitting model equation to the data obtained from macroscopic mechanical tests. This is inadequate since structural features of STZs theory cannot be assessed. Here, we develop anisotropic pair distribution function (PDF) method for directly characterizing mechanical response of deformation defects. Our results reveal the physical picture of deformation defects in BMGs and also provide direct experimental observation of a link between mechanical deformation and intrinsic properties of deformation defects in BMGs.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
