ترغب بنشر مسار تعليمي؟ اضغط هنا

Estimating Lower Limb Kinematics using Distance Measurements with a Reduced Wearable Inertial Sensor Count

123   0   0.0 ( 0 )
 نشر من قبل Luke Wicent Sy
 تاريخ النشر 2020
والبحث باللغة English




اسأل ChatGPT حول البحث

This paper presents an algorithm that makes novel use of distance measurements alongside a constrained Kalman filter to accurately estimate pelvis, thigh, and shank kinematics for both legs during walking and other body movements using only three wearable inertial measurement units (IMUs). The distance measurement formulation also assumes hinge knee joint and constant body segment length, helping produce estimates that are near or in the constraint space for better estimator stability. Simulated experiments shown that inter-IMU distance measurement is indeed a promising new source of information to improve the pose estimation of inertial motion capture systems under a reduced sensor count configuration. Furthermore, experiments show that performance improved dramatically for dynamic movements even at high noise levels (e.g., $sigma_{dist} = 0.2$ m), and that acceptable performance for normal walking was achieved at $sigma_{dist} = 0.1$ m. Nevertheless, further validation is recommended using actual distance measurement sensors.



قيم البحث

اقرأ أيضاً

Goal: This paper presents an algorithm for accurately estimating pelvis, thigh, and shank kinematics during walking using only three wearable inertial sensors. Methods: The algorithm makes novel use of a constrained Kalman filter (CKF). The algorithm iterates through the prediction (kinematic equation), measurement (pelvis position pseudo-measurements, zero velocity update, flat-floor assumption, and covariance limiter), and constraint update (formulation of hinged knee joints and ball-and-socket hip joints). Results: Evaluation of the algorithm using an optical motion capture-based sensor-to-segment calibration on nine participants ($7$ men and $2$ women, weight $63.0 pm 6.8$ kg, height $1.70 pm 0.06$ m, age $24.6 pm 3.9$ years old), with no known gait or lower body biomechanical abnormalities, who walked within a $4 times 4$ m$^2$ capture area shows that it can track motion relative to the mid-pelvis origin with mean position and orientation (no bias) root-mean-square error (RMSE) of $5.21 pm 1.3$ cm and $16.1 pm 3.2^circ$, respectively. The sagittal knee and hip joint angle RMSEs (no bias) were $10.0 pm 2.9^circ$ and $9.9 pm 3.2^circ$, respectively, while the corresponding correlation coefficient (CC) values were $0.87 pm 0.08$ and $0.74 pm 0.12$. Conclusion: The CKF-based algorithm was able to track the 3D pose of the pelvis, thigh, and shanks using only three inertial sensors worn on the pelvis and shanks. Significance: Due to the Kalman-filter-based algorithms low computation cost and the relative convenience of using only three wearable sensors, gait parameters can be computed in real-time and remotely for long-term gait monitoring. Furthermore, the system can be used to inform real-time gait assistive devices.
This paper presents an algorithm that makes novel use of a Lie group representation of position and orientation alongside a constrained extended Kalman filter (CEKF) to accurately estimate pelvis, thigh, and shank kinematics during walking using only three wearable inertial sensors. The algorithm iterates through the prediction update (kinematic equation), measurement update (pelvis height, zero velocity update, flat-floor assumption, and covariance limiter), and constraint update (formulation of hinged knee joints and ball-and-socket hip joints). The paper also describes a novel Lie group formulation of the assumptions implemented in the said measurement and constraint updates. Evaluation of the algorithm on nine healthy subjects who walked freely within a $4 times 4$ m$^2$ room shows that the knee and hip joint angle root-mean-square errors (RMSEs) in the sagittal plane for free walking were $10.5 pm 2.8^circ$ and $9.7 pm 3.3^circ$, respectively, while the correlation coefficients (CCs) were $0.89 pm 0.06$ and $0.78 pm 0.09$, respectively. The evaluation demonstrates a promising application of Lie group representation to inertial motion capture under reduced-sensor-count configuration, improving the estimates (i.e., joint angle RMSEs and CCs) for dynamic motion, and enabling better convergence for our non-linear biomechanical constraints. To further improve performance, additional information relating the pelvis and ankle kinematics is needed.
Goal: This paper presents an algorithm for estimating pelvis, thigh, shank, and foot kinematics during walking using only two or three wearable inertial sensors. Methods: The algorithm makes novel use of a Lie-group-based extended Kalman filter. The algorithm iterates through the prediction (kinematic equation), measurement (pelvis position pseudo-measurements, zero-velocity update, and flat-floor assumption), and constraint update (hinged knee and ankle joints, constant leg lengths). Results: The inertial motion capture algorithm was extensively evaluated on two datasets showing its performance against two standard benchmark approaches in optical motion capture (i.e., plug-in gait (commonly used in gait analysis) and a kinematic fit (commonly used in animation, robotics, and musculoskeleton simulation)), giving insight into the similarity and differences between the said approaches used in different application areas. The overall mean body segment position (relative to mid-pelvis origin) and orientation error magnitude of our algorithm ($n=14$ participants) for free walking was $5.93 pm 1.33$ cm and $13.43 pm 1.89^circ$ when using three IMUs placed on the feet and pelvis, and $6.35 pm 1.20$ cm and $12.71 pm 1.60^circ$ when using only two IMUs placed on the feet. Conclusion: The algorithm was able to track the joint angles in the sagittal plane for straight walking well, but requires improvement for unscripted movements (e.g., turning around, side steps), especially for dynamic movements or when considering clinical applications. Significance: This work has brought us closer to comprehensive remote gait monitoring using IMUs on the shoes. The low computational cost also suggests that it can be used in real-time with gait assistive devices.
The human body is punctuated with wide array of sensory systems that provide a high evolutionary advantage by facilitating formation of a detailed picture of the immediate surroundings. The sensors range across a wide spectrum, acquiring input from n on-contact audio-visual means to contact based input via pressure and temperature. The ambit of sensing can be extended further by imparting the body with increased non-contact sensing capability through the phenomenon of electrostatics. Here we present graphene-based tattoo sensor for proximity sensing, employing the principle of electrostatic gating. The sensor shows a remarkable change in resistance upon exposure to objects surrounded with static charge on them. Compared to prior work in this field, the sensor has demonstrated the highest recorded proximity detection range of 20 cm. It is ultra-thin, highly skin conformal and comes with a facile transfer process such that it can be tattooed on highly curvilinear rough substrates like the human skin, unlike other graphene-based proximity sensors reported before. Present work details the operation of wearable proximity sensor while exploring the effect of mounting body on the working mechanism. A possible role of the sensor as an alerting system against unwarranted contact with objects in public places especially during the current SARS-CoV-2 pandemic has also been explored in the form of an LED bracelet whose color is controlled by the proximity sensor attached to it.
Kalman filtering has been traditionally applied in three application areas of estimation, state estimation, parameter estimation (a.k.a. model updating), and dual estimation. However, Kalman filter is often not sufficient when experimenting with high ly uncertain nonlinear dynamic systems. In this study, a nonlinear estimator is developed by adopting a particle filter algorithm that takes advantage of measured signals. This approach is shown to significantly improve the ability to estimate states. To illustrate this approach, a model for a nonlinear device coupled with a hydraulic actuator plays the role of an actual plant and a nonlinear algebraic function is considered as an approximation of the nonlinear device, thus generating non-parametric and parametric uncertainties. Then we use displacement and force signals to improve the distribution of the states by resampling the set of particles. Finally, all of the states are estimated from these posterior density functions. A set of simulations considering three different noise levels demonstrates that the performance of the particle filter approach is superior to the Kalman filter, yielding substantially better performance when estimating nonlinear physical systems in the presence of modeling uncertainties.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا