اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEvolving basal slip under glaciers and ice streams
65
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Many fast-flowing glaciers and ice streams move over beds consisting of reworked sediments and erosional products, commonly referred to as till. The complex interplay between ice, meltwater, and till at the subglacial bed connects several fundamental problems in glaciology including the debate about rapid mass loss from the ice sheets, the formation and evolution of subglacial landforms, and the storage and transport of subglacial water. In-situ measurements have probed the subglacial bed, but provide surprisingly variable and seemingly inconsistent evidence of the depth where deformation occurs, even at a given field site. These observations suggest that subglacial beds are inherently dynamic. The goal of this paper is to advance our understanding of the physical processes that contribute to the dynamics of subglacial beds as reflected in existing observations of basal deformation. We build on recent advances in modeling dense, granular flows to derive a new numerical model for water-saturated till. Our model demonstrates that changes in the force balance or temporal variations in water pressure can shift slip away from the ice-bed interface and far into the bed, causing episodes of significantly enhanced till transport because the entire till layer above the deep slip interface becomes mobilized. We compare our model results against observations of basal deformation from both mountain glacier and ice-stream settings in the past and present. We also present an analytical solution to assess the variability of till transport for different glacial settings and hydraulic properties.
قيم البحث
اقرأ أيضاً
Biots theory predicts the wave velocities of a saturated poroelastic granular medium from the elastic properties, density and geometry of its dry solid matrix and the pore fluid, neglecting the interaction between constituent particles and local flow
. However, when the frequencies become high and the wavelengths comparable with particle size, the details of the microstructure start to play an important role. Here, a novel hydro-micromechanical numerical model is proposed by coupling the lattice Boltzmann method (LBM) with the discrete element method (DEM. The model allows to investigate the details of the particle-fluid interaction during propagation of elastic waves While the DEM is tracking the translational and rotational motion of each solid particle, the LBM can resolve the pore-scale hydrodynamics. Solid and fluid phases are two-way coupled through momentum exchange. The coupling scheme is benchmarked with the terminal velocity of a single sphere settling in a fluid. To mimic a pressure wave entering a saturated granular medium, an oscillating pressure boundary condition on the fluid is implemented and benchmarked with one-dimensional wave equations. Using a face centered cubic structure, the effects of input waveforms and frequencies on the dispersion relations are investigated. Finally, the wave velocities at various effective confining pressures predicted by the numerical model are compared with with Biots analytical solution, and a very good agreement is found. In addition to the pressure and shear waves, slow compressional waves are observed in the simulations, as predicted by Biots theory.
Data-driven machine-learning for predicting instantaneous and future fault-slip in laboratory experiments has recently progressed markedly due to large training data sets. In Earth however, earthquake interevent times range from 10s-100s of years and
geophysical data typically exist for only a portion of an earthquake cycle. Sparse data presents a serious challenge to training machine learning models. Here we describe a transfer learning approach using numerical simulations to train a convolutional encoder-decoder that predicts fault-slip behavior in laboratory experiments. The model learns a mapping between acoustic emission histories and fault-slip from numerical simulations, and generalizes to produce accurate results using laboratory data. Notably slip-predictions markedly improve using the simulation-data trained-model and training the latent space using a portion of a single laboratory earthquake-cycle. The transfer learning results elucidate the potential of using models trained on numerical simulations and fine-tuned with small geophysical data sets for potential applications to faults in Earth.
We investigate the nature of friction in granular layers by means of numerical simulation focusing on the critical slip distance, over which the system relaxes to a new stationary state. Analyzing a transient process in which the sliding velocity is
instantaneously changed, we find that the critical slip distance is proportional to the sliding velocity. We thus define the relaxation time, which is independent of the sliding velocity. It is found that the relaxation time is proportional to the layer thickness and inversely proportional to the square root of the pressure. An evolution law for the relaxation process is proposed, which does not contain any length constants describing the surface geometry but the relaxation time of the bulk granular matter. As a result, the critical slip distance is scaled with a typical length scale of a system. It is proportional to the layer thickness in an instantaneous velocity change experiment, whereas it is scaled with the total slip distance in a spring-block system on granular layers.
Earthquakes cause lasting changes in static equilibrium, resulting in global deformation fields that can be observed. Consequently, deformation measurements such as those provided by satellite based InSAR monitoring can be used to infer an earthquake
s faulting mechanism. This inverse problem requires a numerical forward model that is both accurate and fast, as typical inverse procedures require many evaluations. The Weakly-enforced Slip Method (WSM) was developed to meet these needs, but it was not before applied in an inverse problem setting. Consequently, it was unknown what effect particular properties of the WSM, notably its inherent continuity, have on the inversion process. Here we show that the WSM is able to accurately recover slip distributions in a Bayesian-inference setting, provided that data points in the vicinity of the fault are removed. In a representative scenario, an element size of 2 km was found to be sufficiently fine to generate a posterior probability distribution that is close to the theoretical optimum. For rupturing faults a masking zone of 20 km sufficed to avoid numerical disturbances that would otherwise be induced by the discretization error. These results demonstrate that the WSM is a viable forward method for earthquake inversion problems. While our synthesized scenario is basic for reasons of validation, our results are expected to generalize to the wider gamut of scenarios that finite element methods are able to capture. This has the potential to bring modeling flexibility to a field that if often forced to impose model restrictions in a concession to computability.
We propose a model for the formation of chromatin loops based on the diffusive sliding of a DNA-bound factor which can dimerise to form a molecular slip-link. Our slip-links mimic the behaviour of cohesin-like molecules, which, along with the CTCF pr
otein, stabilize loops which organize the genome. By combining 3D Brownian dynamics simulations and 1D exactly solvable non-equilibrium models, we show that diffusive sliding is sufficient to account for the strong bias in favour of convergent CTCF-mediated chromosome loops observed experimentally. Importantly, our model does not require any underlying, and energetically costly, motor activity of cohesin. We also find that the diffusive motion of multiple slip-links along chromatin may be rectified by an intriguing ratchet effect that arises if slip-links bind to the chromatin at a preferred loading site. This emergent collective behaviour is driven by a 1D osmotic pressure which is set up near the loading point, and favours the extrusion of loops which are much larger than the ones formed by single slip-links.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
