اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدPermittivity and permeability of epoxy-magnetite powder composites at microwave frequencies
239
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Radio, millimetre and sub-millimetre astronomy experiments as well as remote sensing applications often require castable absorbers with well known electromagnetic properties to design and realize calibration targets. In this context, we fabricated and characterized two samples using different ratios of two easily commercially available materials: epoxy (Stycast 2850FT) and magnetite ($mathrm{Fe_{3}O_{4}}$) powder. We performed transmission and reflection measurements from 7 GHz up to 170 GHz with a VNA equipped with a series of standard horn antennas. Using an empirical model we analysed the data to extract complex permittivity and permeability from transmission data; then we used reflection data to validate the results. In this paper we present the sample fabrication procedure, analysis method, parameter extraction pipeline, and results for two samples with different epoxy-powder mass ratios.
قيم البحث
اقرأ أيضاً
Carbon Nanotubes (CNTs)-polymer composites are promising candidates for a myriad of applications. Ad-hoc CNTs-polymer composite fabrication techniques inherently pose roadblock to optimized processing resulting in microstructural defects i.e., void f
ormation, poor interfacial adhesion, wettability, and agglomeration of CNTs inside the polymer matrix. Although improvement in the microstructures can be achieved via additional processing steps such as-mechanical methods and/or chemical functionalization, the resulting composites are somewhat limited in structural and functional performances. Here, we demonstrate that 3D printing technique like-direct ink writing offers improved processing of CNTs-polymer composites. The shear-induced flow of an engineered nanocomposite ink through the micronozzle offers some benefits including reducing the number of voids within the epoxy, improving CNTs dispersion and adhesion with epoxy, and partially aligns the CNTs. Such microstructural changes result in superior mechanical performance and heat transfer in the composites compared to their mold-casted counterparts. This work demonstrates the advantages of 3D printing over traditional fabrication methods, beyond the ability to rapidly fabricate complex architectures, to achieve improved processing dynamics for fabricating CNT-polymer nanocomposites with better structural and functional properties.
Due to their exceptional mechanical and chemical properties and their natural abundance, cellulose nanocrystals (CNCs) are promising building blocks of sustainable polymer composites. However, the rapid gelation of CNC dispersions has generally limit
ed CNC-based composites to low CNC fractions, in which polymer remains the dominant phase. Here we report on the formulation and processing of crosslinked CNC-epoxy composites with a CNC fraction exceeding 50 wt.%. The microstructure comprises sub-micrometer aggregates of CNCs crosslinked to polymer, which are analogous to the lamellar structure of nacre and promotes toughening mechanisms associated with bulk ductile behavior, despite the brittle behavior of the aggregates at the nanoscale. At 63 wt.% CNCs, the composites exhibit a hardness of 0.66 GPa and a fracture toughness of 5.2 MPa.m$^{1/2}$. The hardness of this all-organic material is comparable to aluminum alloys, and the fracture toughness at the centimeter scale is comparable to that of wood cell wall. We show that CNC-epoxy composite objects can be shaped from the gel precursors by direct-write printing and by casting, while the cured composites can be machined into complex 3D shapes. The formulation, processing route, and the insights on toughening mechanisms gained from our multiscale approach can be applied broadly to highly loaded nanocomposites.
We report quantitative measurements of nanoscale permittivity and conductivity using tuning-fork (TF) based microwave impedance microscopy (MIM). The system is operated under the driving amplitude modulation mode, which ensures satisfactory feedback
stability on samples with rough surfaces. The demodulated MIM signals on a series of bulk dielectrics are in good agreement with results simulated by finite-element analysis. Using the TF-MIM, we have visualized the evolution of nanoscale conductance on back-gated $MoS_2$ field effect transistors and the results are consistent with the transport data. Our work suggests that quantitative analysis of mesoscopic electrical properties can be achieved by near-field microwave imaging with small distance modulation.
We investigate the microwave properties of epoxy-based composite containing melt-extracted CoFeBSiNb microwires fabricated by a combined current-modulation annealing (CCMA) technique. We observe a shift of the resonance peak in the effective permitti
vity spectra of the composite sample containing annealed 25 mm Nb-doped microwires as an applied magnetic field is increased. This observation is consistent with the absorption-dominated impedance for thick microwires and the ferromagnetic resonance phenomenon. It is shown that CCMA is an appropriate technique to release internal residual stresses. Hence, for samples containing small amounts of Nb, we observe that CCMA allows us to suppress the high frequency resonance peak observed in samples containing as-cast wires. However, for samples containing a high amount of Nb, the high frequency peak remains despite the CCMA treatment. In this case, the observation of a two-peak feature in the permittivity spectra is attributed to the coexistence of the amorphous phase and a small amount of nanocrystallites distributed at the wire surface. However, due to large magnetostatic energy of long (35 mm) and short (15 mm) as-cast wires and imperfect wire-epoxy bonding no shift of the resonance peak and the characteristic double peak of the permittivity spectrum can be detected. Overall, CCMA emerges as a promising strategy to control microwave permittivity in composites with melt-extracted microwires.
Metasurfaces advanced the field of optics by reducing the thickness of optical components and merging multiple functionalities into a single layer device. However, this generally comes with a reduction in performance, especially for multifunctional a
nd broadband applications. Three-dimensional metastructures can provide the necessary degrees of freedom for advanced applications, while maintaining minimal thickness. This work explores 3D mechanically reconfigurable devices that perform focusing, spectral demultiplexing, and polarization sorting based on mechanical configuration. As proof of concept, a rotatable device, auxetic device, and a shearing-based device are designed with adjoint-based topology optimization, 3D-printed, and measured at microwave frequencies (7.6-11.6 GHz) in an anechoic chamber.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
