ترغب بنشر مسار تعليمي؟ اضغط هنا

Analysis and Improvement of the Hot Disk Transient Plane Source Method for Low Thermal Conductivity Materials

189   0   0.0 ( 0 )
 نشر من قبل Qiye Zheng
 تاريخ النشر 2019
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

The hot disk transient plane source (TPS) method is a widely used standard technique (ISO 22007-2) for the characterization of thermal properties of materials, especially the thermal conductivity, k. Despite its well-established reliability for a wide variety of common materials, the hot disk TPS method is also known to suffer from a substantial systematic errors when applied to low-k thermal insulation materials. Here, we present a combined numerical and experimental study on the influence of the geometry of hot disk sensor on measured value of low-k materials. We demonstrate that the error is strongly affected by the finite thickness and thermal mass of the sensors insulation layer was well as the corresponding increase of the effective heater size beyond the radius of the embedded metal heater itself. We also numerically investigate the dependence of the error on the sample thermal properties, confirming that the errors are worse in low-k samples. A simple correction function is also provided, which converts the apparent (erroneous) result from a standard hot disk TPS measurement to a more accurate value. A standard polyimide sensor was also optimized using both wet and dry etching to provide more accurate measurement directly. Experimentally corrected value of k for Airloy x56 aerogel and a commercial silica aerogel using the numerical correction factor derived based on the standard TPS sensor is in excellent agreement with the directly measured value from the TPS sensor using the optimized polyimide sensor. Both of these methods can reduce the errors to less than 4% as compared to around 40% error of overestimation from raw values measured with the pristine sensor. Such results show that both the numerical correction to a pristine senor or an optimized sensor are capable of providing highly accurate value of thermal conductivity for such materials.



قيم البحث

اقرأ أيضاً

This study explores the potentialities of Scanning Thermal Microscopy (SThM) technique as a tool for measuring thermal transporting properties of carbon-derived materials issued from thermal conversion of organic polymers, such as the most commonly k nown polyimide (PI), Kapton. For quantitative measurements, the Null Point SThM (NP-SThM) technique is used in order to avoid unwanted effects as the parasitic heat flows through the air and the probe cantilever. Kapton HN films were pyrolysed in an inert atmosphere at temperatures up to 1200{deg}C to produce carbon-based residues with varying degree of conversion to free sp2 disordered carbon. The thermal conductivity of carbon materials ranges from 0.2 to 2 Wm-1K-1 depending on the temperature of the carbonization process (varied between 500{deg}C and 1200{deg}C). In order to validate the applicability of NP-SThM approach to these materials, the results were compared to those obtained with the three more traditional techniques, namely photo-thermal radiometry, flash laser analysis and micro-Raman thermometry. It was found that NP SThM data are in excellent agreement with previous work using more traditional techniques. We used the NP-SThM technique to differentiate structural heterogeneities or imperfections at the surface of the pyrolysed Kapton on the basis of measured local thermal conductivity.
An efficient order$-N$ real-space Kubo approach is developed for the calculation of the thermal conductivity of complex disordered materials. The method, which is based on the Chebyshev polynomial expansion of the time evolution operator and the Lanc zos tridiagonalization scheme, efficiently treats the propagation of phonon wave-packets in real-space and the phonon diffusion coefficients. The mean free paths and the thermal conductance can be determined from the diffusion coefficients. These quantities can be extracted simultaneously for all frequencies, which is another advantage in comparison with the Greens function based approaches. Additionally, multiple scattering phenomena can be followed through the time dependence of the diffusion coefficient deep into the diffusive regime, and the onset of weak or strong phonon localization could possibly be revealed at low temperatures for thermal insulators. The accuracy of our computational scheme is demonstrated by comparing the calculated phonon mean free paths in isotope-disordered carbon nanotubes with Landauer simulations and analytical results. Then, the upscalibility of the method is illustrated by exploring the phonon mean free paths and the thermal conductance features of edge disordered graphene nanoribbons having widths of $sim$20 nanometers and lengths as long as a micrometer, which are beyond the reach of other numerical techniques. It is shown that, the phonon mean free paths of armchair nanoribbons are smaller than those of zigzag nanoribbons for the frequency range which dominate the thermal conductance at low temperatures. This computational strategy is applicable to higher dimensional systems, as well as to a wide range of materials.
227 - A. Sikora , H. Ftouni , J. Richard 2012
A suspended system for measuring the thermal properties of membranes is presented. The sensitive thermal measurement is based on the 3$omega$ dynamic method coupled to a V$ddot{o}$lklein geometry. The device obtained using micro-machining processes a llows the measurement of the in-plane thermal conductivity of a membrane with a sensitivity of less than 10nW/K (+/-$5x10^{-3}$Wm$^{-1}K^{-1}$ at room temperature) and a very high resolution ($Delta K/K =10^{-3}$). A transducer (heater/thermometer) centered on the membrane is used to create an oscillation of the heat flux and to measure the temperature oscillation at the third harmonic using a Wheatstone bridge set-up. Power as low as 0.1nanoWatt has been measured at room temperature. The method has been applied to measure thermal properties of low stress silicon nitride and polycrystalline diamond membranes with thickness ranging from 100 nm to 400 nm. The thermal conductivity measured on the polycrystalline diamond membrane support a significant grain size effect on the thermal transport.
Upon insertion and extraction of lithium, materials important for electrochemical energy storage can undergo changes in thermal conductivity (${Lambda}$) and elastic modulus ($it M$). These changes are attributed to evolution of the intrinsic thermal carrier lifetime and interatomic bonding strength associated with structural transitions of electrode materials with varying degrees of reversibility. Using in situ time-domain thermoreflectance (TDTR) and picosecond acoustics, we systemically study $Lambda$ and $it M$ of conversion, intercalation and alloying electrode materials during cycling. The intercalation V$_{2}$O$_{5}$ and TiO$_{2}$ exhibit non-monotonic reversible ${Lambda}$ and $it M$ switching up to a factor of 1.8 (${Lambda}$) and 1.5 ($it M$) as a function of lithium content. The conversion Fe$_{2}$O$_{3}$ and NiO undergo irreversible decays in ${Lambda}$ and $it M$ upon the first lithiation. The alloying Sb shows the largest and partially reversible order of the magnitude switching in ${Lambda}$ between the delithiated (18 W m$^{-1}$ K$^{-1}$) and lithiated states (<1 W m$^{-1}$ K$^{-1}$). The irreversible ${Lambda}$ is attributed to structural degradation and pulverization resulting from substantial volume changes during cycling. These findings provide new understandings of the thermal and mechanical property evolution of electrode materials during cycling of importance for battery design, and also point to pathways for forming materials with thermally switchable properties.
Electromagnetic induction imaging with atomic magnetometers has disclosed unprecedented domains for imaging, from security screening to material characterization. However, applications to low-conductivity specimens -- most notably for biomedical imag ing -- require sensitivity, stability, and tunability only speculated thus far. Here, we demonstrate contactless and non-invasive imaging down to 50 S/m using a 50 fT/Hz$^{-1/2}$ $^{87}$Rb radio-frequency atomic magnetometer operating in an unshielded environment and near room temperature. Two-dimensional images of test objects are obtained with a near-resonant imaging approach, which reduces the phase noise by a factor 172, with projected sensitivity of 1 S/m. Our results, an improvement of more than three orders of magnitude on previous imaging demonstrations, push electromagnetic imaging with atomic magnetometers to regions of interest for semiconductors, insulators, and biological tissues.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا