ترغب بنشر مسار تعليمي؟ اضغط هنا

RF Chain Reduction for MIMO Systems: A Hardware Prototype

145   0   0.0 ( 0 )
 نشر من قبل Tierui Gong
 تاريخ النشر 2019
والبحث باللغة English




اسأل ChatGPT حول البحث

Radio frequency (RF) chain circuits play a major role in digital receiver architectures, allowing passband communication signals to be processed in baseband. When operating at high frequencies, these circuits tend to be costly. This increased cost imposes a major limitation on future multiple-input multiple-output (MIMO) communication technologies. A common approach to mitigate the increased cost is to utilize hybrid architectures, in which the received signal is combined in analog into a lower dimension, thus reducing the number of RF chains. In this work we study the design and hardware implementation of hybrid architectures via minimizing channel estimation error. We first derive the optimal solution for complex-gain combiners and propose an alternating optimization algorithm for phase-shifter combiners. We then present a hardware prototype implementing analog combining for RF chain reduction. The prototype consists of a specially designed configurable combining board as well as a dedicated experimental setup. Our hardware prototype allows evaluating the effect of analog combining in MIMO systems using actual communication signals. The experimental study, which focuses on channel estimation accuracy in MIMO channels, demonstrates that using the proposed prototype, the achievable channel estimation performance is within a small gap in a statistical sense from that obtained using a costly receiver in which each antenna is connected to a dedicated RF chain.



قيم البحث

اقرأ أيضاً

The requirement of high data-rate in the fifth generation wireless systems (5G) calls for the ultimate utilization of the wide bandwidth in the mmWave frequency band. Researchers seeking to compensate for mmWaves high path loss and to achieve both ga in and directivity have proposed that mmWave multiple-input multiple-output (MIMO) systems make use of beamforming systems. Hybrid beamforming in mmWave demonstrates promising performance in achieving high gain and directivity by using phase shifters at the analog processing block. What remains a problem, however, is the actual implementation of mmWave beamforming systems; to fabricate such a system is costly and complex. With the aim of reducing such cost and complexity, this article presents actual prototypes of the lens antenna as an effective device to be used in the future 5G mmWave hybrid beamforming systems. Using a lens as a passive phase shifter enables beamforming without the heavy network of active phase shifters, while gain and directivity are achieved by the energy-focusing property of the lens. Proposed in this article are two types of lens antennas, one for static and the other for mobile usage. Their performance is evaluated using measurements and simulation data along with link-level analysis via a software defined radio (SDR) platform. Results show the promising potential of the lens antenna for its high gain and directivity, and its improved beam-switching feasibility compared to when a lens is not used. System-level evaluations reveal the significant throughput enhancement in both real indoor and outdoor environments. Moreover, the lens antennas design issues are also discussed by evaluating different lens sizes.
Analog Multiple-Input Multiple-Output Radio-over-Copper (A-MIMO-RoC) is an effective all-analog FrontHaul (FH) architecture that exploits any pre-existing Local Area Network (LAN) cabling infrastructure of buildings to distribute Radio-Frequency (RF) signals indoors. A-MIMO-RoC, by leveraging a fully analog implementation, completely avoids any dedicated digital interface by using a transparent end-to-end system, with consequent latency, bandwidth and cost benefits. Usually, LAN cables are exploited mainly in the low-frequency spectrum portion, mostly due to the moderate cable attenuation and crosstalk among twisted-pairs. Unlike current systems based on LAN cables, the key feature of the proposed platform is to exploit more efficiently the huge bandwidth capability offered by LAN cables, that contain 4 twisted-pairs reaching up to 500 MHz bandwidth/pair when the length is below 100 m. Several works proposed numerical simulations that assert the feasibility of employing LAN cables for indoor FH applications up to several hundreds of MHz, but an A-MIMO-RoC experimental evaluation is still missing. Here, we present some preliminary results obtained with an A-MIMO-RoC prototype made by low-cost all-analog/all-passive devices along the signal path. This setup demonstrates experimentally the feasibility of the proposed analog relaying of MIMO RF signals over LAN cables up to 400 MHz, thus enabling an efficient exploitation of the LAN cables transport capabilities for 5G indoor applications.
116 - Gui Zhou , Cunhua Pan , Hong Ren 2020
In this paper, intelligent reflecting surface (IRS) is proposed to enhance the physical layer security in the Rician fading channel where the angular direction of the eavesdropper is aligned with a legitimate user. In this scenario, we consider a two -phase communication system under the active attacks and passive eavesdropping. Particularly, in the first phase, the base station avoids direct transmission to the attacked user. While, in the second phase, other users cooperate to forward signals to the attacked user with the help of IRS and energy harvesting technology. Under the active attacks, we investigate an outage constrained beamforming design problem under the statistical cascaded channel error model, which is solved by using the Bernstein-type inequality. As for the passive eavesdropping, an average secrecy rate maximization problem is formulated, which is addressed by a low complexity algorithm. Numerical results show that the negative effect of the eavesdroppers channel error is greater than that of the legitimate user.
Millimeter-wave (mmWave) multiple-input multiple-output (MIMO) system for the fifth generation (5G) cellular communications can also enable single-anchor positioning and object tracking due to its large bandwidth and inherently high angular resolutio n. In this paper, we introduce the newly invented concept, large intelligent surface (LIS), to mmWave positioning systems, study the theoretical performance bounds (i.e., Cramer-Rao lower bounds) for positioning, and evaluate the impact of the number of LIS elements and the value of phase shifters on the position estimation accuracy compared to the conventional scheme with one direct link and one non-line-of-sight path. It is verified that better performance can be achieved with a LIS from the theoretical analyses and numerical study.
Channel estimation is of crucial importance in massive multiple-input multiple-output (m-MIMO) visible light communication (VLC) systems. In order to tackle this problem, a fast and flexible denoising convolutional neural network (FFDNet)-based chann el estimation scheme for m-MIMO VLC systems was proposed. The channel matrix of the m-MIMO VLC channel is identified as a two-dimensional natural image since the channel has the characteristic of sparsity. A deep learning-enabled image denoising network FFDNet is exploited to learn from a large number of training data and to estimate the m-MIMO VLC channel. Simulation results demonstrate that our proposed channel estimation based on the FFDNet significantly outperforms the benchmark scheme based on minimum mean square error.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا