اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدExperimental demonstration of dynamical input isolation in nonadiabatically modulated photonic cavities
100
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Modulated optical cavities have been proposed and demonstrated for applications in communications, laser frequency stabilization, microwave-to-optical conversion and frequency comb generation. However, most studies are restricted to the adiabatic regime, where either the maximum excursion of the modulation or the modulation frequency itself is below the linewidth of the cavity. Here, using a fiber ring resonator with an embedded electro-optic phase modulator, we investigate the nonadiabatic regime. By strongly driving the modulator at frequencies that are significantly smaller than the free-spectral range of the ring resonator, but well beyond the linewidth of the resonator, we experimentally observe counterintuitive behavior predicted in a recent theoretical study by Minkov et al. [APL Photonics 2, 076101 (2017)], such as the complete suppression of drop-port transmission even when the input laser wavelength is on resonance with the optical cavity. This can be understood as dynamical isolation of the cavity from the input light. We also show qualitative differences in the steady-state responses of the system between the adiabatic and nonadiabatic limits. Our experiments probe a seldom explored regime of operation that is promising for applications in integrated photonic systems with current state-of-the-art technology.
قيم البحث
اقرأ أيضاً
We experimentally demonstrate high Quality factor dual-polarized TE-TM photonic crystal nanobeam cavities. The free-standing nanobeams are fabricated in a 500 nm thick silicon layer, and are probed using both tapered optical fiber and free-space reso
nant scattering set-ups. We measure Q-factors greater than 10^4 for both TM and TE modes, and observe large fiber transmission drops (0.3 -- 0.4) at the TM mode resonances.
We demonstrate experimentally that the spectral broadening of CW supercontinuum can be controlled by using photonic crystal fibers with two zero-dispersion wavelengths pumped by an Yb fiber laser at 1064 nm. The spectrum is bounded by two dispersive
waves whose spectral location depends on the two zero-dispersion wavelengths of the fiber. The bandwidth of the generated spectrum and the spectral power density may thus be tailored for particular applications, such as high-resolution optical coherence tomography or optical spectroscopy.
We have constructed and experimentally tested a microwave half waveplate using the dispersive birefringent properties of a bulk two-dimensional photonic crystal away from its band gap. Our waveplate device exhibited a 200:1 polarization contrast, lim
ited by our experimental resolution. We anticipate that photonic crystal waveplates will have important practical applications in several areas, including integrated photonic circuits.
We describe the design, fabrication, and spectroscopy of coupled, high Quality (Q) factor silicon nanobeam photonic crystal cavities. We show that the single nanobeam cavity modes are coupled into even and odd superposition modes, and we simulate the
frequency and Q factor as a function of nanobeam spacing, demonstrating that a differential wavelength shift of 70 nm between the two modes is possible while maintaining Q factors greater than 10^6. For both on-substrate and free-standing nanobeams, we experimentally monitor the response of the even mode as the gap is varied, and measure Q factors as high as 200,000.
Wavelength-scale, high Q-factor photonic crystal cavities have emerged as a platform of choice for on-chip manipulation of optical signals, with applications ranging from low-power optical signal processing and cavity quantum electrodynamics, to bioc
hemical sensing. Many of these applications, however, are limited by the fabrication tolerances and the inability to precisely control the resonant wavelength of fabricated structures. Various techniques for post-fabrication wavelength trimming and dynamical wavelength control -- using, for example, thermal effects, free carrier injection, low temperature gas condensation, and immersion in fluids -- have been explored. However, these methods are often limited by small tuning ranges, high power consumption, or the inability to tune continuously or reversibly. In this letter, by combining nano-electro-mechanical systems (NEMS) and nanophotonics, we demonstrate reconfigurable photonic crystal nanobeam cavities that can be continuously and dynamically tuned using electrostatic forces. A tuning of ~10 nm has been demonstrated with less than 6 V of external bias and negligible steady-state power consumption.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
