اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThe effect of adding magnetic oxide as grain boundary for HAMR
61
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Grain-to-grain Curie temperature (Tc) variation in the media reduces signal-to-noise ratio due to its contribution in transition jitter noise, especially when average grain size is pushing down to increase the area storage capacity. A thermally insulating magnetic grain boundary may suppress such grain-to-grain Tc variation, especially at small grain size. Here we present an experimental study on the effect of adding thermally-insulating magnetic oxide, in particular BaFexOy, as part of the grain boundary materials in granular FePt-C HAMR media. It is found that the BaFexOy is chemically inert to FePt and the chemical ordering of FePt-BaFexOy-C media are similar to that of FePt-C meida. By tuning the volume fraction of BaFexOy and C, well-separated FePt grains (average grain size = 6.8 nm) surrounded by BaFexOy shell with perpendicular Hc above 35 kOe can be obtained. Transmission electron microscopy study with chemical analysis shows that the magnetic oxide appears to be crystalline and surround the FePt grains with immediate full enclosure. Magnetic measurements indicate an effective increase of magnetic grain size at temperatures below FePt Curie temperature. Pulsed laser pump-probe measurement indicates a measurable reduction of Curie temperature variation for the FePt-BaFexOy-C media with carefully comparison with the reference FePt-C media.
قيم البحث
اقرأ أيضاً
A detailed theoretical and numerical investigation of the infinitesimal single-crystal gradient plasticity and grain-boundary theory of Gurtin (2008) A theory of grain boundaries that accounts automatically for grain misorientation and grain-boundary
orientation. Journal of the Mechanics and Physics of Solids 56 (2), 640-662, is performed. The governing equations and flow laws are recast in variational form. The associated incremental problem is formulated in minimization form and provides the basis for the subsequent finite element formulation. Various choices of the kinematic measure used to characterize the ability of the grain boundary to impede the flow of dislocations are compared. An alternative measure is also suggested. A series of three-dimensional numerical examples serve to elucidate the theory.
Mg grain boundary (GB) segregation and GB diffusion can impact the processing and properties of Al-Mg alloys. Yet, Mg GB diffusion in Al has not been measured experimentally or predicted by simulations. We apply atomistic computer simulations to pred
ict the amount and the free energy of Mg GB segregation, and the impact of segregation on GB diffusion of both alloy components. At low temperatures, Mg atoms segregated to a tilt GB form clusters with highly anisotropic shapes. Mg diffuses in Al GBs slower than Al itself, and both components diffuse slowly in comparison with Al GB self-diffusion. Thus, Mg segregation significantly reduces the rate of mass transport along GBs in Al-Mg alloys. The reduced atomic mobility can be responsible for the improved stability of the microstructure at elevated temperatures.
While it is known that alloy components can segregate to grain boundaries (GBs), and that the atomic mobility in GBs greatly exceeds the atomic mobility in the lattice, little is known about the effect of GB segregation on GB diffusion. Atomistic com
puter simulations offer a means of gaining insights into the segregation-diffusion relationship by computing the GB diffusion coefficients of the alloy components as a function of their segregated amounts. In such simulations, thermodynamically equilibrium GB segregation is prepared by a semi-grand canonical Monte Carlo method, followed by calculation of the diffusion coefficients of all alloy components by molecular dynamics. As a demonstration, the proposed methodology is applied to a GB is the Cu-Ag system. The GB diffusivities obtained exhibit non-trivial composition dependencies that can be explained by site blocking, site competition, and the onset of GB disordering due to the premelting effect.
The study of the interaction between graphene oxide and arsenic is of great relevance towards the development of adsorbent materials and as a way to understand how these two materials interact in the environment. In this work we show that As(III) ads
orption, primarily H3AsO3, by graphene oxide is dependent on its degree of oxidation. Variations in the concentration of potassium permanganate resulted in an increase on the C/O ratio from 1.98 to 1.35 with C-OH and C-O-C concentrations of 18 and 32%, respectively. Three oxidation degrees were studied, the less oxidized material reached a maximum As(III) adsorption capacity of 124 mg/g, whereas the graphene with the highest degree of oxidation reached a value of 288 mg/g at pH 7, to the authors knowledge, the highest reported in the literature. The interaction between graphene oxide and As(III) was also studied by Density Functional Theory (DFT) computer models showing that graphene oxide interacts with As(III) primarily through hydrogen bonds, having interaction energies with the hydroxyl and epoxide groups of 378 and 361 kcal/mol, respectively. Finally, cytotoxicity tests showed that the graphene oxide had a cellular viability of 57% with 50 {mu}g/ml, regardless of its degree of oxidation.
Electric fields and currents, which are used in innovative materials processing and electrochemical energy conversion, can often alter microstructures in unexpected ways. However, little is known about the underlying mechanisms. Using ZnO-Bi2O3 as a
model system, this study uncovers how an applied electric current can change the microstructural evolution through an electrochemically induced grain boundary (GB) transition. By combining aberration-corrected electron microscopy, photoluminescence spectroscopy, first-principles calculations, a generalizable thermodynamic model, and ab initio molecular dynamics, this study reveals that electrochemical reduction can cause a GB disorder-to-order transition to markedly increase GB diffusivities and mobilities. Consequently, abruptly enhanced or abnormal grain growth takes place. These findings advance our fundamental knowledge of GB complexion (phase-like) transitions and electric field effects on microstructural stability and evolution, with broad scientific and technological impacts. A new method to tailor the GB structures and properties, as well as the microstructures, electrochemically can also be envisioned.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
