اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدGraphene-enabled, directed nanomaterial placement from solution for large-scale device integration
441
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Controlled placement of nanomaterials at predefined locations with nanoscale precision remains among the most challenging problems that inhibit their large-scale integration in the field of semiconductor process technology. Methods based on surface functionalization have a drawback where undesired chemical modifications can occur and deteriorate the deposited material. The application of electric-field assisted placement techniques eliminates the element of chemical treatment; however, it requires an incorporation of conductive placement electrodes that limit the performance, scaling, and density of integrated electronic devices. Here, we report a method for electric-field assisted placement of solution-processed nanomaterials by using large-scale graphene layers featuring nanoscale deposition sites. The structured graphene layers are prepared via either transfer or synthesis on standard substrates, then are removed without residue once nanomaterial deposition is completed, yielding material assemblies with nanoscale resolution that cover surface areas larger than 1mm2. In order to demonstrate the broad applicability, we have assembled representative zero-, one-, and two-dimensional semiconductors at predefined substrate locations and integrated them into nanoelectronic devices. This graphene-based placement technique affords nanoscale resolution at wafer scale, and could enable mass manufacturing of nanoelectronics and optoelectronics involving a wide range of nanomaterials prepared via solution-based approaches.
قيم البحث
اقرأ أيضاً
Controlled atomic scale fabrication of functional devices is one of the holy grails of nanotechnology. The most promising class of techniques that enable deterministic nanodevice fabrication are based on scanning probe patterning or surface assembly.
However, this typically involves a complex process flow, stringent requirements for an ultra high vacuum environment, long fabrication times and, consequently, limited throughput and device yield. Here, a device platform is developed that overcomes these limitations by integrating scanning probe based dopant device fabrication with a CMOS-compatible process flow. Silicon on insulator substrates are used featuring a reconstructed Si(001):H surface that is protected by a capping chip and has pre-implanted contacts ready for scanning tunneling microscope (STM) patterning. Processing in ultra-high vacuum is thus reduced to only a few critical steps which minimizes the complexity, time and effort required for fabrication of the nanoscale dopant devices. Subsequent reintegration of the samples into the CMOS process flow not only simplifies the post-processing but also opens the door to successful application of STM based dopant devices as a building block in more complex device architectures. Full functionality of this approach is demonstrated with magnetotransport measurements on degenerately doped STM patterned Si:P nanowires up to room temperature.
Accurate extraction of liquid is the first step towards low-volume liquid delivery and nanocharacterization, which plays a significant role in biomedical research. In this study, a tip-shaped graphene nanopipette (GNP) is proposed by encapsulating th
e biomolecule solution on the prefabricated metal tip with graphene. The volume of the encapsulated liquid is highly controllable at zeptoliter precision by tuning the encapsulating speed and the number of graphene encapsulation rounds. Using protein (ferritin) solution as an example, it has been confirmed by finite element analysis and the controlled experiments that the GNP allows the delivery of ferritin solution at the zeptoliter-scale. Furthermore, GNP is demonstrated as a new type of tip-shaped liquid cell, which is suitable for multiple nanocharacterization techniques. In particular, due to the ultra-sharp tip shape, isotope (13C)-labelled glucose solution encapsulated in GNP has been characterized by atom probe tomography (APT) in the laser-pulsed mode. Analysis of the mass spectrum and the reconstructed three-dimensional chemical maps reveals the quantitative distribution and the compositions of individual glucose molecules. The GNP is expected to be introduced to deliver liquid in the range of zeptoliters to attoliters, and brings a new capability for characterization of biological specimens in their near-native state.
Graphene and related materials can lead to disruptive advances in next generation photonics and optoelectronics. The challenge is to devise growth, transfer and fabrication protocols providing high (>5,000 cm2 V-1 s-1) mobility devices with reliable
performance at the wafer scale. Here, we present a flow for the integration of graphene in photonics circuits. This relies on chemical vapour deposition (CVD) of single layer graphene (SLG) matrices comprising up to ~12000 individual single crystals (SCs), grown to match the geometrical configuration of the devices in the photonic circuit. This is followed by a transfer approach which guarantees coverage over ~80% of the device area, and integrity for up to 150 mm wafers, with room temperature mobility ~5000 cm2 V-1 s-1. We use this process flow to demonstrate double SLG electro-absorption modulators with modulation efficiency ~0.25, 0.45, 0.75, 1 dB V-1 for device lengths ~30, 60, 90, 120 {mu}m. The data rate is up to 20 Gbps. Encapsulation with single-layer hBN is used to protected SLG during plasma-enhanced CVD of Si3N4, ensuring reproducible device performance. Our full process flow (from growth to device fabrication) enables the commercial implementation of graphene-based photonic devices.
We propose a concentrated thermionic emission solar cell design, which demonstrates a high solar-to-electricity energy conversion efficiency larger than 10% under 600 sun, by harnessing the exceptional electrical, thermal and radiative properties of
the graphene as a collector electrode. By constructing an analytical model that explicitly takes into account the non-Richardson behavior of the thermionic emission current from graphene, space charge effect in vacuum gap, and the various irreversible energy losses within the subcomponents, we perform a detailed characterization on the conversion efficiency limit and electrical power output characteristics of the proposed system. We systematically model and compare the energy conversion efficiency of various configurations of graphene-graphene and graphene-diamond and diamond-diamond thermionic emitter, and show that utilizing diamond films as an emitter and graphene as a collector offers the highest maximum efficiency, thus revealing the important role of graphene in achieving high-performance thermionic emission solar cell. A maximum efficiency of 12.8% under 800 sun has been revealed, which is significantly higher than several existing solid-state solar cell designs, such as the solar-driven thermoelectric and thermophotovoltaic converters. Our work thus opens up new avenues to advance the efficiency limit of thermionic solar energy conversion and the development of next-generation novel-nanomaterial-based solar energy harvesting technology.
Although photoelectrochemical water splitting is likely to be an important and powerful tool to provide environmentally friendly hydrogen, most developments in this field have been conducted on a laboratory scale so far. In order for the technology t
o make a sizeable impact on the energy transition, scaled up devices made of inexpensive and earth abundant materials must be developed. In this work, we demonstrate a scalable (64 cm2 aperture area) artificial photoelectrochemical device composed of triple-junction thin-film silicon solar cells in conjunction with an electrodeposited bifunctional nickel iron molybdenum water splitting catalyst. Our device shows a solar to hydrogen efficiency of up to 4.67% (5.33% active area) without bias assistance and wire connection. Furthermore, gas separation was enabled by incorporating a membrane in a 3D printed device frame.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
