ترغب بنشر مسار تعليمي؟ اضغط هنا

Shape dependence of resistance force exerted on an obstacle placed in a gravity-driven granular silo flow

156   0   0.0 ( 0 )
 نشر من قبل Hiroaki Katsuragi
 تاريخ النشر 2017
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

Resistance force exerted on an obstacle in a gravity-driven slow granular silo flow is studied by experiments and numerical simulations. In a two-dimensional granular silo, an obstacle is placed just above the exit. Then, steady discharge flow is made and its flow rate can be controlled by the width of exit and the position of obstacle. During the discharge of particles, flow rate and resistance force exerting on the obstacle are measured. Using the obtained data, a dimensionless number characterizing the force balance in granular flow is defined by the relation between the discharge flow rate and resistance-force decreasing rate. The dimensionless number is independent of flow rate. Rather, we find the weak shape dependence of the dimensionless number. This tendency is a unique feature for the resistance force in granular silo flow. It characterizes the effective flow width interacting with the obstacle in granular silo flow.



قيم البحث

اقرأ أيضاً

We propose an explanation for the onset of oscillations seen in numerical simulations of dense, inclined flows of inelastic, frictional spheres. It is based on a phase transition between disordered and ordered collisional states that may be interrupt ed by the formation of force chains. Low frequency oscillations between ordered and disordered states take place over weakly bumpy bases; higher-frequency oscillations over strongly bumpy bases involve the formation of particle chains that extend to the base and interrupt the phase change. The predicted frequency and amplitude of the oscillations induced by the unstable part of the equation of state are similar to those seen in the simulations and they depend upon the contact stiffness in the same way. Such oscillations could be the source of sound produced by flowing sand.
Granular fronts are a common yet unexplained phenomenon emerging during the gravity driven free-surface flow of concentrated suspensions. They are usually believed to be the result of fluid convection in combination with particle size segregation. Ho wever, suspensions composed of uniformly sized particles also develop a granular front. Within a large rotating drum, a stationary recirculating avalanche is generated. The flowing material is a mixture of a visco-plastic fluid obtained from a kaolin-water dispersion, with spherical ceramic particles denser than the fluid. The goal is to mimic the composition of many common granular-fluid materials, like fresh concrete or debris flow. In these materials, granular and fluid phases have the natural tendency to segregate due to particle settling. However, through the shearing caused by the rotation of the drum, a reorganization of the phases is induced, leading to the formation of a granular front. By tuning the material properties and the drum velocity, it is possible to control this phenomenon. The setting is reproduced in a numerical environment, where the fluid is solved by a Lattice-Boltzmann Method, and the particles are explicitly represented using the Discrete Element Method. The simulations confirm the findings of the experiments, and provide insight into the internal mechanisms. Comparing the time-scale of particle settling with the one of particle recirculation, a non-dimensional number is defined, and is found to be effective in predicting the formation of a granular front.
We study the flow of elongated grains (wooden pegs of length $L$=20 mm with circular cross section of diameter $d_c$=6 and 8 mm) from a silo with a rotating bottom and a circular orifice of diameter $D$. In the small orifice range ($D/d<5$) clogs are mostly broken by the rotating base, and the flow is intermittent with avalanches and temporary clogs. Here $dequiv(frac{3}{2}d_c^2L)^{1/3}$ is the effective grain diameter. Unlike for spherical grains, for rods the flow rate $W$ clearly deviates from the power law dependence $Wpropto (D-kd)^{2.5}$ at lower orifice sizes in the intermittent regime, where $W$ is measured in between temporary clogs only. Instead, below about $D/d<3$ an exponential dependence $Wpropto e^{kappa D}$ is detected. Here $k$ and $kappa$ are constants of order unity. Even more importantly, rotating the silo base leads to a strong -- more than 50% -- decrease of the flow rate, which otherwise does not depend significantly on the value of $omega$ in the continuous flow regime. In the intermittent regime, $W(omega)$ appears to follow a non-monotonic trend, although with considerable noise. A simple picture, in terms of the switching from funnel flow to mass flow and the alignment of the pegs due to rotation, is proposed to explain the observed difference between spherical and elongated grains. We also observe shear induced orientational ordering of the pegs at the bottom such that their long axes in average are oriented at a small angle $langlethetarangle approx 15^circ$ to the motion of the bottom.
The shape of a microchannel during flow through it is instrumental to understanding the physics that govern various phenomena ranging from rheological measurements of fluids to separation of particles and cells. Two commonly used approaches for obtai ning a desired channel shape (for a given application) are (i) fabricating the microchannel in the requisite shape and (ii) actuating the microchannel walls during flow to obtain the requisite shape. However, these approaches are not always viable. We propose an alternative, passive approach to {it a priori} tune the elastohydrodynamics in a microsystem, towards achieving a pre-determined (but not pre-fabricated) flow geometry when the microchannel is subjected to flow. That is to say, we use the interaction between a soft solid layer, the viscous flow beneath it and the shaped rigid wall above it, to tune the fluid domains shape. Specifically, we study a parallel-wall microchannel whose top wall is a slender soft coating of arbitrary thickness attached to a rigid platform. We derive a nonlinear differential equation for the soft coatings fluid--solid interface, which we use to infer how to achieve specific conduit shapes during flow. Using this theory, we demonstrate the tuning of four categories of microchannel geometries, which establishes, via a proof-of-concept, the viability of our modeling framework. We also explore slip length patterning on the rigid bottom wall of the microchannel, a common technique in microfluidics, as an addition `handle for microchannel shape control. However, we show that this effect is much weaker in practice.
As a natural and functional behavior, various microorganisms exhibit gravitaxis by orienting and swimming upwards against gravity. Swimming autophoretic nanomotors described herein, comprising bimetallic nanorods, preferentially orient upwards and sw im up along a wall, when tail-heavy (i.e. when the density of one of the metals is larger than the other). Through experiment and theory, two mechanisms were identified that contribute to this gravitactic behavior. First, a buoyancy or gravitational torque acts on these rods to align them upwards. Second, hydrodynamic interactions of the rod with the inclined wall induce a fore-aft drag asymmetry on the rods that reinforces their orientation bias and promotes their upward motion.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا