اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدDirect prediction of the solute softening-to-hardening transition in W-Re alloys using stochastic simulations of screw dislocation motion
66
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Interactions among dislocations and solute atoms are the basis of several important processes in metals plasticity. In body-centered cubic (bcc) metals and alloys, low-temperature plastic flow is controlled by screw dislocation glide, which is known to take place by the nucleation and sideward relaxation of kink pairs across two consecutive emph{Peierls} valleys. In alloys, dislocations and solutes affect each others kinetics via long-range stress field coupling and short-range inelastic interactions. It is known that in certain substitutional bcc alloys a transition from solute softening to solute hardening is observed at a critical concentration. In this paper, we develop a kinetic Monte Carlo model of screw dislocation glide and solute diffusion in substitutional W-Re alloys. We find that dislocation kinetics is governed by two competing mechanisms. At low solute concentrations, nucleation is enhanced by the softening of the Peierls stress, which overcomes the elastic repulsion of Re atoms on kinks. This trend is reversed at higher concentrations, resulting in a minimum in the flow stress that is concentration and temperature dependent. This minimum marks the transition from solute softening to hardening, which is found to be in reasonable agreement with experiments.
قيم البحث
اقرأ أيضاً
High-temperature, high-dose, neutron irradiation of W results in the formation of Re-rich clusters at concentrations one order of magnitude lower than the thermodynamic solubility limit. These clusters may eventually transform into brittle W-Re inter
metallic phases, which can lead to high levels of hardening and thermal conductivity losses. Standard theories of radiation enhanced diffusion and precipitation cannot explain the formation of these precipitates and so understanding the mechanism by which nonequilibrium clusters form under irradiation is crucial to predict materials degradation and devise mitigation strategies. Here we carry out a thermodynamic study of W-Re alloys and conduct kinetic Monte Carlo simulations of Re cluster formation in irradiated W-2Re alloys using a generalized Hamiltonian for crystals containing point defects parameterized entirely with electronic structure calculations. Our model incorporates recently-gained mechanistic information of mixed-interstitial solute transport, which is seen to control cluster nucleation and growth by forming quasi-spherical nuclei after an average incubation time of 20 s at 1800 K. These nuclei are seen to grow by attracting more mixed interstitials bringing solute atoms, which in turns attracts vacancies leading to recombination and solute agglomeration. The clusters grow to a maximum size of approximately 4-nm radius, and are not fully dense with Re, containing 50% or less near the center. Our simulations are in reasonable agreement with recent atom probe examinations of ion irradiated W-2Re systems at 773 K.
Dislocation velocities and mobilities are studied by Molecular Dynamics simulations for edge and screw dislocations in pure aluminum and nickel, and edge dislocations in Al-2.5%Mg and Al-5.0%Mg random substitutional alloys using EAM potentials. In th
e pure materials, the velocities of all dislocations are close to linear with the ratio of (applied stress)/(temperature) at low velocities, consistent with phonon drag models and quantitative agreement with experiment is obtained for the mobility in Al. At higher velocities, different behavior is observed. The edge dislocation velocity remains dependent solely on (applied stress)/(temperature) up to approximately 1.0 MPa/K, and approaches a plateau velocity that is lower than the smallest forbidden speed predicted by continuum models. In contrast, above a velocity around half of the smallest continuum wave speed, the screw dislocation damping has a contribution dependent solely on stress with a functional form close to that predicted by a radiation damping model of Eshelby. At the highest applied stresses, there are several regimes of nearly constant (transonic or supersonic) velocity separated by velocity gaps in the vicinity of forbidden velocities; various modes of dislocation disintegration and destabilization were also encountered in this regime. In the alloy systems, there is a temperature- and concentration-dependent pinning regime where the velocity drops sharply below the pure metal velocity. Above the pinning regime but at moderate stresses, the velocity is again linear in (applied stress)/(temperature) but with a lower mobility than in the pure metal.
The classical motion of gliding dislocation lines in slip planes of crystalline solid helium leads to plastic deformation even at temperatures far below the Debye temperature and can affect elastic properties. In this work we argue that the gliding o
f dislocations and plasticity may be the origin of many observed elastic anomalies in solid He-4, which have been argued to be connected to supersolidity. We present a dislocation motion model that describes the stress-strain $tau$-$epsilon$ curves and work hardening rate $dtau/depsilon$ of a shear experiment performed at constant strain rate $dot{epsilon}$ in solid helium. The calculated $dtau/depsilon$ exhibits strong softening with increasing temperature due to the motion of dislocations, which mimics anomalous softening of the elastic shear modulus $mu$. In the same temperature region the motion of dislocations causes dissipation with a prominent peak.
The critical resolved shear stress of an Al 4 wt. % Cu alloy containing a homogeneous distribution of $theta$ precipitates was determined by means of dislocation dynamics simulations. The size distribution, shape, orientation and volume fraction of t
he precipitates in the alloy were obtained from transmission electron microscopy observations while the parameters controlling the dislocation/precipitate interactions (elastic mismatch, transformation strains, dislocation mobility and cross-slip probability, etc.) were calculated from atomistic simulations. The precipitates were assumed to be either impenetrable or shearable by the dislocations, the latter characterized by a threshold shear stress that has to be overcome to shear the precipitate. The predictions of the simulations in terms of the critical resolved shear stress and of the dislocation/precipitate interaction mechanisms were in good agreement with the experimental results. It was concluded that the optimum strength of this alloy is attained with a homogeneous distribution of $theta$ precipitates whose average size ($approx$ 40 nm) is at the transition between precipitate shearing and looping. Overall, the dislocation dynamics strategy presented in this paper is able to provide quantitative predictions of precipitate strengthening in metallic alloys.
The ability of a body-centered cubic metal to deform plastically is limited by the thermally activated glide motion of screw dislocations, which are line defects with a mobility exhibiting complex dependence on temperature, stress, and dislocation se
gment length. We derive an analytical expression for the velocity of dislocation glide, based on a statistical mechanics argument, and identify an apparent phase transition marked by a critical temperature above which the activation energy for glide effectively halves, changing from the formation energy of a double kink to that of a single kink. The analysis is in quantitative agreement with direct kinetic Monte Carlo simulations.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
