اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدDynamic tunable notch filters for the Antarctic Impulsive Transient Antenna (ANITA)
94
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The Antarctic Impulsive Transient Antenna (ANITA) is a NASA long-duration balloon experiment with the primary goal of detecting ultra-high-energy ($>10^{18},mbox{eV}$) neutrinos via the Askaryan Effect. The fourth ANITA mission, ANITA-IV, recently flew from Dec 2 to Dec 29, 2016. For the first time, the Tunable Universal Filter Frontend (TUFF) boards were deployed for mitigation of narrow-band, anthropogenic noise with tunable, switchable notch filters. The TUFF boards also performed second-stage amplification by approximately 45 dB to boost the $sim,mumbox{V-level}$ radio frequency (RF) signals to $sim$ mV-level for digitization, and supplied power via bias tees to the first-stage, antenna-mounted amplifiers. The other major change in signal processing in ANITA-IV is the resurrection of the $90^{circ}$ hybrids deployed previously in ANITA-I, in the trigger system, although in this paper we focus on the TUFF boards. During the ANITA-IV mission, the TUFF boards were successfully operated throughout the flight. They contributed to a factor of 2.8 higher total instrument livetime on average in ANITA-IV compared to ANITA-III due to reduction of narrow-band, anthropogenic noise before a trigger decision is made.
قيم البحث
اقرأ أيضاً
A Monte Carlo simulation program for the radio detection of Ultra High Energy (UHE) neutrino interactions in the Antarctic ice as viewed by the Antarctic Impulsive Transient Antenna (ANITA) is described in this article. The program, icemc, provides a
n input spectrum of UHE neutrinos, the parametrization of the Askaryan radiation generated by their interaction in the ice, and the propagation of the radiation through ice and air to a simulated model of the third and fourth ANITA flights. This paper provides an overview of the icemc simulation, descriptions of the physics models used and of the ANITA electronics processing chain, data/simulation comparisons to validate the predicted performance, and a summary of the impact of published results.
We present a detailed report on the experimental details of the Antarctic Impulsive Transient Antenna (ANITA) long duration balloon payload, including the design philosophy and realization, physics simulations, performance of the instrument during it
s first Antarctic flight completed in January of 2007, and expectations for the limiting neutrino detection sensitivity. Neutrino physics results will be reported separately.
The primary science goal of the NASA-sponsored ANITA project is measurement of ultra-high energy neutrinos and cosmic rays, observed via radio-frequency signals resulting from a neutrino- or cosmic ray- interaction with terrestrial matter (atmospheri
c or ice molecules, e.g.). Accurate inference of the energies of these cosmic rays requires understanding the transmission/reflection of radio wave signals across the ice-air boundary. Satellite-based measurements of Antarctic surface reflectivity, using a co-located transmitter and receiver, have been performed more-or-less continuously for the last few decades. Satellite-based reflectivity surveys, at frequencies ranging from 2--45 GHz and at near-normal incidence, yield generally consistent reflectivity maps across Antarctica. Using the Sun as an RF source, and the ANITA-3 balloon borne radio-frequency antenna array as the RF receiver, we have also measured the surface reflectivity over the interval 200-1000 MHz, at elevation angles of 12-30 degrees, finding agreement with the Fresnel equations within systematic errors. To probe low incidence angles, inaccessible to the Antarctic Solar technique and not probed by previous satellite surveys, a novel experimental approach (HiCal-1) was devised. Unlike previous measurements, HiCal-ANITA constitute a bi-static transmitter-receiver pair separated by hundreds of kilometers. Data taken with HiCal, between 200--600 MHz shows a significant departure from the Fresnel equations, constant with frequency over that band, with the deficit increasing with obliquity of incidence, which we attribute to the combined effects of possible surface roughness, surface grain effects, radar clutter and/or shadowing of the reflection zone due to Earth curvature effects.
The balloon-borne HiCal radio-frequency (RF) transmitter, in concert with the ANITA radio-frequency receiver array, is designed to measure the Antarctic surface reflectivity in the RF wavelength regime. The amplitude of surface-reflected transmission
s from HiCal, registered as triggered events by ANITA, can be compared with the direct transmissions preceding them by O(10) microseconds, to infer the surface power reflection coefficient $cal{R}$. The first HiCal mission (HiCal-1, Jan. 2015) yielded a sample of 100 such pairs, resulting in estimates of $cal{R}$ at highly-glancing angles (i.e., zenith angles approaching $90^circ$), with measured reflectivity for those events which exceeded extant calculations. The HiCal-2 experiment, flying from Dec., 2016-Jan., 2017, provided an improvement by nearly two orders of magnitude in our event statistics, allowing a considerably more precise mapping of the reflectivity over a wider range of incidence angles. We find general agreement between the HiCal-2 reflectivity results and those obtained with the earlier HiCal-1 mission, as well as estimates from Solar reflections in the radio-frequency regime. In parallel, our calculations of expected reflectivity have matured; herein, we use a plane-wave expansion to estimate the reflectivity R from both a flat, smooth surface (and, in so doing, recover the Fresnel reflectivity equations) and also a curved surface. Multiplying our flat-smooth reflectivity by improved Earth curvature and surface roughness corrections now provides significantly better agreement between theory and the HiCal 2a/2b measurements.
OSIRIS (Optical System for Imaging and low Resolution Integrated Spectroscopy) is the first light instrument of the Gran Telescopio Canarias (GTC). It provides a flexible and competitive tunable filter (TF). Since it is based on a Fabry-Perot interfe
rometer working in collimated beam, the TF transmission wavelength depends on the position of the target with respect to the optical axis. This effect is non-negligible and must be accounted for in the data reduction. Our paper establishes a wavelength calibration for OSIRIS TF with the accuracy required for spectrophotometric measurements using the full field of view (FOV) of the instrument. The variation of the transmission wavelength $lambda(R)$ across the FOV is well described by $lambda(R)=lambda(0)/sqrt{1+(R/f_2)^2}$, where $lambda(0)$ is the central wavelength, $R$ represents the physical distance from the optical axis, and $f_2=185.70pm0.17,$mm is the effective focal length of the camera lens. This new empirical calibration yields an accuracy better than 1,AA across the entire OSIRIS FOV ($sim$8arcmin$times$8arcmin), provided that the position of the optical axis is known within 45 $mu$m ($equiv$ 1.5 binned pixels). We suggest a calibration protocol to grant such precision over long periods, upon re-alignment of OSIRIS optics, and in different wavelength ranges. This calibration differs from the calibration in OSIRIS manual which, nonetheless, provides an accuracy $lesssim1$AA, for $Rlesssim 2arcmin$.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
