اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدDemo: WiSCoP - Wireless Sensor Communication Prototyping Platform
59
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
To enhance system performance of future heterogeneous wireless networks the co-design of PHY, MAC, and higher layer protocols is inevitable. In this work, we present WiSCoP - a novel embedded platform for experimentation, prototyping and implementation of integrated cross-layer network design approaches. WiSCoP is built on top of a Zynq hardware platform integrated with FMCOMMS1/2/4 RF front ends. We demonstrate the flexibility of WiSCoP by using it to prototype a fully standard compliant IEEE 802.15.4 stack with real-time performance and cross-layer integration.
قيم البحث
اقرأ أيضاً
An energy cooperation policy for energy harvesting wireless sensor networks (WSNs) with wireless power transfer is proposed in this paper to balance the energy at each sensor node and increase the total energy utilization ratio of the whole WSNs. Con
sidering the unbalanced spatio-temporal properties of the energy supply across the deployment terrain of energy harvesting WSNs and the dynamic traffic load at each sensor node, the energy cooperation problem among sensor nodes is decomposed into two steps: the local energy storage at each sensor node based on its traffic load to meet its own needs; within the energy storage procedure sensor nodes with excess energy transmit a part of their energy to nodes with energy shortage through the energy trading. Inventory theory and game theory are respectively applied to solving the local energy storage problem at each sensor node and the energy trading problem among multiple sensor nodes. Numerical results show that compared with the static energy cooperation method without energy trading, the Stackelberg Model based Game we design in this paper can significantly improve the trading volume of energy thereby increasing the utilization ratio of the harvested energy which is unevenly distributed in the WSNs.
One of the key enablers of future wireless communications is constituted by massive multiple-input multiple-output (MIMO) systems, which can improve the spectral efficiency by orders of magnitude. However, in existing massive MIMO systems, convention
al phased arrays are used for beamforming, which result in excessive power consumption and hardware cost. Recently, reconfigurable intelligent surface (RIS) has been considered as one of the revolutionary technologies to enable energy-efficient and smart wireless communications, which is a two-dimensional structure with a large number of passive elements. In this paper, we propose and develop a new type of high-gain yet low-cost RIS having 256 elements. The proposed RIS combines the functions of phase shift and radiation together on an electromagnetic surface, where positive intrinsic-negative (PIN) diodes are used to realize 2-bit phase shifting for beamforming. Based on this radical design, the worlds first wireless communication prototype using RIS having 256 2-bit elements is designed and developed. Specifically, the prototype conceived consists of modular hardware and flexible software, including the hosts for parameter setting and data exchange, the universal software radio peripherals (USRPs) for baseband and radio frequency (RF) signal processing, as well as the RIS for signal transmission and reception. Our performance evaluation confirms the feasibility and efficiency of RISs in future wireless communications. More particularly, it is shown that a 21.7 dBi antenna gain can be obtained by the proposed RIS at 2.3 GHz, while at the millimeter wave (mmWave) frequency, i.e., 28.5 GHz, a 19.1 dBi antenna gain can be achieved. Furthermore, the over-the-air (OTA) test results show that the RIS-based wireless communication prototype developed is capable of significantly reducing the power consumption.
Wireless sensor networks (WSNs) can be a valuable decision-support tool for farmers. This motivated our deployment of a WSN system to support rain-fed agriculture in India. We defined promising use cases and resolved technical challenges throughout a
two-year deployment of our COMMON-Sense Net system, which provided farmers with environment data. However, the direct use of this technology in the field did not foster the expected participation of the population. This made it difficult to develop the intended decision-support system. Based on this experience, we take the following position in this paper: currently, the deployment of WSN technology in developing regions is more likely to be effective if it targets scientists and technical personnel as users, rather than the farmers themselves. We base this claim on the lessons learned from the COMMON-Sense system deployment and the results of an extensive user experiment with agriculture scientists, which we describe in this paper.
Wireless sensor/actuator networks (WSANs) are emerging as a new generation of sensor networks. Serving as the backbone of control applications, WSANs will enable an unprecedented degree of distributed and mobile control. However, the unreliability of
wireless communications and the real-time requirements of control applications raise great challenges for WSAN design. With emphasis on the reliability issue, this paper presents an application-level design methodology for WSANs in mobile control applications. The solution is generic in that it is independent of the underlying platforms, environment, control system models, and controller design. To capture the link quality characteristics in terms of packet loss rate, experiments are conducted on a real WSAN system. From the experimental observations, a simple yet efficient method is proposed to deal with unpredictable packet loss on actuator nodes. Trace-based simulations give promising results, which demonstrate the effectiveness of the proposed approach.
In sensor networks communication by broadcast methods involves many hazards, especially collision. Several MAC layer protocols have been proposed to resolve the problem of collision namely ARBP, where the best achieved success rate is 90%. We hereby
propose a MAC protocol which achieves a greater success rate (Success rate is defined as the percentage of delivered packets at the source reaching the destination successfully) by reducing the number of collisions, but by trading off the average propagation delay of transmission. Our proposed protocols are also shown to be more energy efficient in terms of energy dissipation per message delivery, compared to the currently existing protocol.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
