اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدUsing coherent X-rays to directly measure the propagation velocity of defects during thin film deposition
82
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The properties of artificially grown thin films are often strongly affected by the dynamic relationship between surface growth processes and subsurface structure. Coherent mixing of X-ray signals promises to provide an approach to better understand such processes. Here, we demonstrate the continuously variable mixing of surface and bulk scattering signals during real-time studies of sputter deposition of a-Si and a-WiS2 films by controlling the X-ray penetration and escape depths in coherent grazing incidence small angle X-ray scattering (Co-GISAXS). Under conditions where the X-ray signal comes from both the growth surface and the thin film bulk, oscillations in temporal correlations arise from coherent interference between scattering from stationary bulk features and from the advancing surface. We also observe evidence that elongated bulk features propagate upward at the same velocity as the surface. Additionally, a highly surface sensitive mode is demonstrated that can access the surface dynamics independently of the subsurface structure.
قيم البحث
اقرأ أيضاً
The properties of artificially grown thin films are strongly affected by surface processes during growth. Coherent X-rays provide an approach to better understand such processes and fluctuations far from equilibrium. Here we report results for vacuum
deposition of C$_{60}$ on a graphene-coated surface investigated with X-ray Photon Correlation Spectroscopy in surface-sensitive conditions. Step-flow is observed through measurement of the step-edge velocity in the late stages of growth after crystalline mounds have formed. We show that the step-edge velocity is coupled to the terrace length, and that there is a variation in the velocity from larger step spacing at the center of crystalline mounds to closely-spaced, more slowly propagating steps at their edges. The results extend theories of surface growth, since the behavior is consistent with surface evolution driven by processes that include surface diffusion, the motion of step-edges, and attachment at step edges with significant step-edge barriers.
Understanding surface dynamics during epitaxial film growth is key to growing high quality materials with controllable properties. X-ray photon correlation spectroscopy (XPCS) using coherent x-rays opens new opportunities for in situ observation of a
tomic-scale fluctuation dynamics during crystal growth. Here, we present the first XPCS measurements of 2D island dynamics during homoepitaxial growth in the layer-by-layer mode. Analysis of the results using two-time correlations reveals a new phenomenon - a memory effect in island nucleation sites on successive crystal layers. Simulations indicate that this persistence in the island arrangements arises from communication between islands on different layers via adatoms. With the worldwide advent of new coherent x-ray sources, the XPCS methods pioneered here will be widely applicable to atomic-scale processes on surfaces.
We present results on growth of large area epitaxial ReS2 thin film both on c plane sapphire substrate and MoS2 template by pulsed laser deposition (PLD). Films tend to grow with (0001) ReS2 perpendicular to (0001) Al2O3 and (0001) ReS2 perpendicular
to (0001) MoS2 parallel to (0001) Al2O3 at deposition temperature below 300 deg C. Films are polycrystalline grown at temperature above 300 deg C. The smoothness and quality of the films are significantly improved when grown on MoS2 template compared to sapphire substrate. The results show that PLD is suitable to grow ReS2 epitaxial thin film over large area for practical device application.
The current driven motion of skyrmions in MnSi and FeGe thinned single crystals could be initiated at current densities of the order of $10^6$ A/m, five orders of magnitude smaller than for magnetic domain walls. The technologically crucial step of r
eplicating these results in thin films has not been successful to date, but the reasons are not clear. Elucidating them requires analyzing system characteristics at scales of few nm where the key Dzyaloshinskii Moriya (DM) interactions vary, and doing so in near application conditions, i.e. oxidation protected systems at room temperature. In this works magnetic force microscopy (MFM) studies of magnetron sputtered Ir/Co/Pt multilayers we show skyrmions that are smaller than previously observed, are not circularly symmetric, and are pinned to 50 nm wide areas of 75 percent higher than average DM interaction. This finding matches our measurement of Co layer thickness inhomogeneity of the order of $pm$1.2 atomic monolayers per 0.6 nm layer, and indicates that layer flatness must be controlled with greater precision to preclude skyrmion pinning.
In this study, the characteristics of nickel thin film deposited by remote plasma atomic layer deposition (RPALD) on p-type Si substrate and formation of nickel silicide using rapid thermal annealing were determined. Bis(1,4-di-isopropyl-1,3-diazabut
adienyl)nickel, Ni(iPr-DAD)2, was used as a Ni precursor and ammonia plasma was used as a reactant. This was the first attempt to deposit Ni thin film using Ni(iPr-DAD)2 as a precursor for the ALD process. The RPALD Ni film was deposited with a growth rate of around 2.2{AA}/cycle at 250 {deg}C and showed significant low resistivity of 33 {mu}{Omega}cm with a total impurity concentration of around 10 at. %.The impurities of the thin film, carbon and nitrogen, were existent by the forms of C-C and C-N in a bonding state. The impurities removal tendency was investigated by comparing of experimental conditions, namely process temperature and pressure. Nitrogen impurity was removed by thermal desorption during each ALD cycle and carbon impurity was reduced by the optimizing of the process pressure which is directly related with a mean free path of NH3 plasma. After Ni deposition, nickel silicide was formed by RTA in a vacuum ambient for 1 minute. A nickel silicide layer from ALD Ni and PVD Ni was compared at the annealing temperature from 500 to 900 {deg}C. NiSi from ALD Ni showed better thermal stability due to the contribution of small amounts of carbon and nitrogen in the asdeposited Ni thin film. Degradation of the silicide layer was effectively suppressed with a use of ALD Ni.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
