اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThe NOAO KOSMOS Data Handling System
110
0
0.0
(
0
)
تأليف
Rob Seaman
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
KOSMOS and COSMOS are twin high-efficiency imaging spectrographs that have been deployed as NOAO facility instruments for the Mayall 4-meter telescope on Kitt Peak in Arizona and for the Blanco telescope on Cerro Tololo in Chile, respectively. The NOAO Data Handling System (DHS) has seen aggressive use over several years at both the Blanco and Mayall telescopes with NEWFIRM (the NOAO Extremely Wide-Field Infrared Imager) and the Mosaic-1.1 wide-field optical imager. Both of these instruments also rely on the Monsoon array controller and related software, and on instrument-specif
قيم البحث
اقرأ أيضاً
We describe the design, construction and measured performance of the Kitt Peak Ohio State Multi-Object Spectrograph (KOSMOS) for the 4-m Mayall telescope and the Cerro Tololo Ohio State Multi-Object Spectrograph (COSMOS) for the 4-m Blanco telescope.
These nearly identical imaging spectrographs are modifie
The ASTRI project is the INAF (Italian National Institute for Astrophysics) flagship project developed in the context of the Cherenkov Telescope Array (CTA) international project. ASTRI is dedicated to the realization of the prototype of a Cherenkov
small-size dual-mirror telescope (SST-2M) and then to the realization of a mini-array composed of a few of these units. The prototype and all the necessary hardware devices are foreseen to be installed at the Serra La Nave Observing Station (Catania, Italy) in 2014. The upcoming data flow will be properly reduced by dedicated (online and offline) analysis pipelines aimed at providing robust and reliable scientific results (signal detection, sky maps, spectra and light curves) from the ASTRI silicon photo-multipliers camera raw data. Furthermore, a flexible archiving system has being conceived for the storage of all the acquired ASTRI (scientific, calibration, housekeeping) data at different steps of the data reduction up to the final scientific products. In this contribution we present the data acquisition, the analysis pipeline and the archive architecture that will be in use for the ASTRI SST prototype. In addition, the generalization of the data management system to the case of a mini-array of ASTRI telescopes will be discussed.
The NOAO NEWFIRM Pipeline produces instrumentally calibrated data products and data quality measurements from all exposures taken with the NOAO Extremely Wide-Field Infrared Imager (NEWFIRM) at the KPNO Mayall 4-meter telescope. We describe the distr
ibuted nature of the NEWFIRM Pipeline, the calibration data that are applied, the data quality metadata that are derived, and the data products that are delivered by the NEWFIRM Pipeline.
To asses stability against 1/f noise, the Low Frequency Instrument (LFI) onboard the Planck mission will acquire data at a rate much higher than the data rate allowed by its telemetry bandwith of 35.5 kbps. The data are processed by an onboard pipeli
ne, followed onground by a reversing step. This paper illustrates the LFI scientific onboard processing to fit the allowed datarate. This is a lossy process tuned by using a set of 5 parameters Naver, r1, r2, q, O for each of the 44 LFI detectors. The paper quantifies the level of distortion introduced by the onboard processing, EpsilonQ, as a function of these parameters. It describes the method of optimizing the onboard processing chain. The tuning procedure is based on a optimization algorithm applied to unprocessed and uncompressed raw data provided either by simulations, prelaunch tests or data taken from LFI operating in diagnostic mode. All the needed optimization steps are performed by an automated tool, OCA2, which ends with optimized parameters and produces a set of statistical indicators, among them the compression rate Cr and EpsilonQ. For Planck/LFI the requirements are Cr = 2.4 and EpsilonQ <= 10% of the rms of the instrumental white noise. To speedup the process an analytical model is developed that is able to extract most of the relevant information on EpsilonQ and Cr as a function of the signal statistics and the processing parameters. This model will be of interest for the instrument data analysis. The method was applied during ground tests when the instrument was operating in conditions representative of flight. Optimized parameters were obtained and the performance has been verified, the required data rate of 35.5 Kbps has been achieved while keeping EpsilonQ at a level of 3.8% of white noise rms well within the requirements.
This paper is part of the Prelaunch status LFI papers published on JINST (http://www.iop.org/EJ/journal/-page=extra.proc5/1748-0221). Plancks Low Frequency Instrument is an array of 22 pseudo-correlation radiometers at 30, 44, and 70 GHz. Before in
tegrating the overall array assembly, a first set of tests has been performed for each radiometer chain assembly (RCA), consisting of two radiometers. In this paper, we describe Rachel, a software application which has been purposely developed and used during the RCA test campaign to carry out both near-realtime on-line data analysis and data storage (in FITS format) of the raw output from the radiometric chains.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
