اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدUltra-low-loss tapered optical fibers with minimal lengths
431
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We design and fabricate ultra-low-loss tapered optical fibers (TOFs) with minimal lengths. We first optimize variations of the torch scan length using the flame-brush method for fabricating TOFs with taper angles that satisfy the adiabaticity criteria. We accordingly fabricate TOFs with optimal shapes and compare their transmission to TOFs with a constant taper angle and TOFs with an exponential shape. The highest transmission measured for TOFs with an optimal shape is in excess of 99.7 % with a total TOF length of only 23 mm, whereas TOFs with a constant taper angle of 2 mrad reach 99.6 % transmission for a 63 mm TOF length.
قيم البحث
اقرأ أيضاً
We investigated the cause of optical transmittance degradation in tapered fibers. Degradation commences immediately after fabrication and it eventually reduces the transmittance to almost zero. It is a major problem that limits applications of tapere
d fibers. We systematically investigated the effect of the dust-particle density and the humidity on the degradation dynamics. The results clearly show that the degradation is mostly due to dust particles and that it is not related to the humidity. In a dust free environment it is possible to preserve the transmittance with a degradation of less than the noise (+/- ?0.02) over 1 week.
We present a novel method of machining optical fiber surfaces with a CO${}_2$ laser for use in Fiber-based Fabry-Perot Cavities (FFPCs). Previously FFPCs were prone to large birefringence and limited to relatively short cavity lengths ($le$ 200 $mu$m
). These characteristics hinder their use in some applications such as cavity quantum electrodynamics with trapped ions. We optimized the laser machining process to produce large, uniform surface structures. This enables the cavities to achieve high finesse even for long cavity lengths. By rotating the fibers around their axis during the laser machining process the asymmetry resulting from the lasers transverse mode profile is eliminated. Consequently we are able to fabricate fiber mirrors with a high degree of rotational symmetry, leading to remarkably low birefringence. Through measurements of the cavity finesse over a range of cavity lengths and the polarization dependence of the cavity linewidth, we confirmed the quality of the produced fiber mirrors for use in low-birefringence FFPCs.
We demonstrate the fabrication of ultra-low-loss, all-fiber Fabry-Perot cavities containing a nanofiber section, optimized for cavity quantum electrodynamics. By continuously monitoring the finesse and fiber radius during fabrication of a nanofiber b
etween two fiber Bragg gratings, we are able to precisely evaluate taper transmission as a function of radius. The resulting cavities have an internal round-trip loss of only 0.31% at a nanofiber waist radius of 207 nm, with a total finesse of 1380, and a maximum expected internal cooperativity of $sim$ 1050 for a cesium atom on the nanofiber surface. Our ability to fabricate such high-finesse nanofiber cavities may open the door for the realization of high-fidelity scalable quantum networks.
Realization of integrated photonic circuits on a single chip requires controlled manipulation and integration of solid-state quantum emitters with nanophotonic components. Previous works focused on emitters embedded in a three-dimensional crystals --
such as nanodiamonds or quantum dots. In contrast, in this work we demonstrate coupling of a single emitter in a two-dimensional (2D) material, namely hexagonal boron nitride (hBN), with a tapered optical fiber and find a collection efficiency of the system is found to be 10~%. Furthermore, due to the single dipole character of the emitter, we were able to analyse the angular emission pattern of the coupled system via back focal plane imaging. The good coupling efficiency to the tapered fiber even allows excitation and detection in a fully fiber coupled way yielding a true integrated system. Our results provide evidence of the feasibility to efficiently integrate quantum emitters in 2D materials with photonic structures.
We demonstrate adiabatically tapered fibers terminating in sub-micron tips that are clad with a higher-index material for coupling to an on-chip waveguide. This cladding enables coupling to a high-index waveguide without losing light to the buried ox
ide. A technique to clad the tip of the tapered fiber with a higher-index polymer is introduced. Conventional tapered waveguides and forked tapered waveguide structures are investigated for coupling from the clad fiber to the on-chip waveguide. We find the forked waveguide facilitates alignment and packaging, while the conventional taper leads to higher bandwidth. The insertion loss from a fiber through a forked coupler to a sub-micron silicon nitride waveguide is 1.1 dB and the 3 dB-bandwidth is 90 nm. The coupling loss in the packaged device is 1.3 dB. With a fiber coupled to a conventional tapered waveguide, the loss is 1.4 dB with a 3 dB bandwidth extending beyond the range of the measurement apparatus, estimated to exceed 250 nm.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
