اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدModeling heat transfer from quench protection heaters to superconducting cables in Nb3Sn magnets
87
0
0.0
(
0
)
نشر من قبل
Scientific Information Service CERN
تاريخ النشر
2014
مجال البحث
فيزياء
والبحث باللغة
English
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We use a recently developed quench protection heater modeling tool for an analysis of heater delays in superconducting high-field Nb3Sn accelerator magnets. The results suggest that the calculated delays are consistent with experimental data, and show how the heater delay depends on the main heater design parameters.
قيم البحث
اقرأ أيضاً
In the years 2009-2013 the Large Hadron Collider (LHC) has been operated with the top beam energies of 3.5 TeV and 4 TeV per proton (from 2012) instead of the nominal 7 TeV. The currents in the superconducting magnets were reduced accordingly. To dat
e only seventeen beam-induced quenches have occurred; eight of them during specially designed quench tests, the others during injection. There has not been a single beam- induced quench during normal collider operation with stored beam. The conditions, however, are expected to become much more challenging after the long LHC shutdown. The magnets will be operating at near nominal currents, and in the presence of high energy and high intensity beams with a stored energy of up to 362 MJ per beam. In this paper we summarize our efforts to understand the quench levels of LHC superconducting magnets. We describe beam-loss events and dedicated experiments with beam, as well as the simulation methods used to reproduce the observable signals. The simulated energy deposition in the coils is compared to the quench levels predicted by electro-thermal models, thus allowing to validate and improve the models which are used to set beam-dump thresholds on beam-loss monitors for Run 2.
The EuCARD project aims on construction of a 19 T hybrid dipole; it will be made of a 6 T HTS dipole associated to a 13 T outsert Nb3Sn dipole [1]. This paper reviews the quench analysis and protection of the 13 T Nb3Sn dipole.
Along with the protection of magnets and power converters, we have added a section on personnel protection because this is our highest priority in the design and operation of power systems. Thus, our topics are the protection of people, power convert
ers, and magnet loads (protected from the powering equipment), including normal conducting magnets and superconducting magnets.
Low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to sup
erconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). The magnet designs are proposed which provide high operating gradient and magnetic field in a large aperture to accommodate the large size of muon beams due to low b{eta}* as well as the cooling system to intercept the large heat deposition from the showers induced by decay electrons. Specific distribution of heat deposition in the lattice elements MC SR requires large aperture magnets to accommodate thick high-Z absorbers to protect the SC coils. Based on the developed MARS15 model and intense simulations, a sophisticated radiation protection system was designed for the collider SR and IR to bring the peak power density in the superconducting coils below the quench limit and reduce the dynamic heat deposition in the cold mass by a factor of 100. The system consists of tight tungsten masks in the magnet interconnect regions and elliptical tungsten liners in magnet aperture optimized for each magnet. It also reduces the background particle fluxes in the collider detector.
Beam transfer, such as injection into or extraction from an accelerator, is one of the most critical moments in terms of machine protection in a high-intensity machine. Special equipment is used and machine protection aspects have to be taken into ac
count in the design of the beam transfer concepts. A brief introduction of the principles of beam transfer and the equipment involved will be given in this lecture. The main concepts of machine protection for injection and extraction will be presented, with examples from the CERN SPS and LHC.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
