اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدLayer number determination in graphene using out-of-plane vibrations
136
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We present a double-resonant Raman mode in few-layer graphene, which is able to probe the number of graphene layers reliably. This so-called N mode on the low-frequency side of the G mode results from a double-resonant Stokes/anti-Stokes process combining a LO and a ZO phonon. Simulations of the double-resonant Raman spectra in bilayer graphene show very good agreement with the experiments. The investigation of the out-of-plane ZO phonon for layer number determination is expected to be transferable to other layered materials like boron nitride.
قيم البحث
اقرأ أيضاً
Correct defect quantification in graphene samples is crucial both for fundamental and applied re-search. Raman spectroscopy represents the most widely used tool to identify defects in graphene. However, despite its extreme importance the relation bet
ween the Raman features and the amount of defects in multilayered graphene samples has not been experimentally verified. In this study we intentionally created defects in single layer graphene, turbostratic bilayer graphene and Bernal stacked bilayer graphene by oxygen plasma. By employing isotopic labelling, our study reveals substantial differences of the effects of plasma treatment on individual layers in bilayer graphene with different stacking orders. In addition Raman spectroscopy evidences scattering of phonons in the bottom layer by defects in the top layer for Bernal-stacked samples, which can in general lead to overestimation of the number of defects by as much as a factor of two.
The electronic properties of few-layer graphene grown on the carbon-face of silicon carbide (SiC) are found to be strongly dependent on the number of layers. The carrier mobility is larger in thicker graphene because substrate-related scattering is r
educed in the higher layers. The carrier density dependence of the mobility is qualitatively different in thin and thick graphene, with the transition occurring at about 2 layers. The mobility increases with carrier density in thick graphene, similar to multi-layer graphene exfoliated from natural graphite, suggesting that the individual layers are still electrically coupled in spite of reports recording non-Bernal stacking order in C-face grown graphene. The Hall coefficient peak value is reduced in thick graphene due to the increased density of states. A reliable and rapid characterization tool for the layer number is therefore highly desirable. To date, AFM height determination and Raman scattering are typically used since the optical contrast of graphene on SiC is weak. However, both methods suffer from low throughput. We show that the scanning electron microscopy (SEM) contrast can give similar results with much higher throughput.
We report on the charge spill-out and work function of epitaxial few-layer graphene on 6H-SiC(0001). Experiments from high-resolution, energy-filtered X-ray photoelectron emission microscopy (XPEEM) are combined with ab initio Density Functional Theo
ry calculations using a relaxed interface model. Work function values obtained from theory and experiments are in qualitative agreement, reproducing the previously observed trend of increasing work function with each additional graphene plane. Electrons transfer at the SiC/graphene interface through a buffer layer causes an interface dipole moment which is at the origin of the graphene work function modulation. The total charge transfer is independent of the number of graphene layers, and is consistent with the constant binding energy of the SiC component of the C 1s core-level measured by XPEEM. Charge leakage into vacuum depends on the number of graphene layers explaining why the experimental, layer-dependent C 1s-graphene core-level binding energy shift does not rigidly follow that of the work function. Thus, a combination of charge transfer at the SiC/graphene interface and charge spill-out into vacuum resolves the apparent discrepancy between the experimental work function and C1s binding energy.
Molybdenum disulfide (MoS2) of single and few-layer thickness was exfoliated on SiO2/Si substrate and characterized by Raman spectroscopy. The number of S-Mo-S layers of the samples was independently determined by contact-mode atomic-force microscopy
. Two Raman modes, E12g and A1g, exhibited sensitive thickness dependence, with the frequency of the former decreasing and that of the latter increasing with thickness. The results provide a convenient and reliable means for determining layer thickness with atomic-level precision. The opposite direction of the frequency shifts, which cannot be explained solely by van der Waals interlayer coupling, is attributed to Coulombic interactions and possible stacking-induced changes of the intralayer bonding. This work exemplifies the evolution of structural parameters in layered materials in changing from the 3-dimensional to the 2-dimensional regime.
Phosphorene has been rediscovered recently, establishing itself as one of the most promising two dimensional group-V elemental monolayers with direct band gap, high carrier mobility, and anisotropic electronic properties. In this letter, the buckling
and its effect on the electronic properties in phosphorene are investigated by using molecular dynamics simulations and complemented by density functional theory calculations. We find that phosphorene shows superior out-of-plane structural flexibility along the armchair direction, which allows the formation of buckling with large curvatures, while the buckling along the zigzag direction will break its structure integrity at large curvatures. The semiconducting and direct band gap nature are retained with buckling along the armchair direction; the band gap decreases and transforms to an indirect band gap with buckling along the zigzag direction. The structural flexibility and electronic robustness along the armchair direction facilitate the fabrication of devices with complex shapes, such as folded phosphorene and phosphorene nano-scrolls, thereby offering new possibilities for the application of phosphorene in flexible electronics and optoelectronics.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
