اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEpitaxial and layer-by-layer growth of EuO thin films on yttria-stabilized cubic zirconia (001) using MBE distillation
372
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We have succeeded in growing epitaxial and highly stoichiometric films of EuO on yttria-stabilized cubic zirconia (YSZ) (001). The use of the Eu-distillation process during the molecular beam epitaxy assisted growth enables the consistent achievement of stoichiometry. We have also succeeded in growing the films in a layer-by-layer fashion by fine tuning the Eu vs. oxygen deposition rates. The initial stages of growth involve the limited supply of oxygen from the YSZ substrate, but the EuO stoichiometry can still be well maintained. The films grown were sufficiently smooth so that the capping with a thin layer of aluminum was leak tight and enabled ex situ experiments free from trivalent Eu species. The findings were used to obtain recipes for better epitaxial growth of EuO on MgO (001).
قيم البحث
اقرأ أيضاً
We have succeeded in preparing high-quality Gd-doped single-crystalline EuO films. Using Eu-distillation-assisted molecular beam epitaxy and a systematic variation in the Gd and oxygen deposition rates, we have been able to observe sustained layer-by
-layer epitaxial growth on yttria-stabilized cubic zirconia (001). The presence of Gd helps to stabilize the layer-by-layer growth mode. We used soft x-ray absorption spectroscopy at the Eu and Gd M4,5 edges to confirm the absence of Eu3+ contaminants and to determine the actual Gd concentration. The distillation process ensures the absence of oxygen vacancies in the films. From magnetization measurements we found the Curie temperature to increase smoothly as a function of doping from 70 K up to a maximum of 125 K. A threshold behavior was not observed for concentrations as low as 0.2%.
Voltage control of interfacial magnetism has been greatly highlighted in spintronics research for many years, as it might enable ultra-low power technologies. Among few suggested approaches, magneto-ionic control of magnetism has demonstrated large m
odulation of magnetic anisotropy. Moreover, the recent demonstration of magneto-ionic devices using hydrogen ions presented relatively fast magnetization toggle switching, tsw ~ 100 ms, at room temperature. However, the operation speed may need to be significantly improved to be used for modern electronic devices. Here, we demonstrate that the speed of proton-induced magnetization toggle switching largely depends on proton-conducting oxides. We achieve ~1 ms reliable (> 103 cycles) switching using yttria-stabilized zirconia (YSZ), which is ~ 100 times faster than the state-of-the-art magneto-ionic devices reported to date at room temperature. Our results suggest further engineering of the proton-conducting materials could bring substantial improvement that may enable new low-power computing scheme based on magneto-ionics.
We report on the layer-by-layer growth of single-crystal Al2O3 thin-films on Nb (110). Single-crystal Nb films are first prepared on A-plane sapphire, followed by the evaporation of Al in an O2 background. The first stages of Al2O3 growth are layer-b
y-layer with hexagonal symmetry. Electron and x-ray diffraction measurements indicate the Al2O3 initially grows clamped to the Nb lattice with a tensile strain near 10%. This strain relaxes with further deposition, and beyond about 5 nm we observe the onset of island growth. Despite the asymmetric misfit between the Al2O3 film and the Nb under-layer, the observed strain is surprisingly isotropic.
Graphene is a 2D material that displays excellent electronic transport properties with prospective applications in many fields. Inducing and controlling magnetism in the graphene layer, for instance by proximity of magnetic materials, may enable its
utilization in spintronic devices. This paper presents fabrication and detailed characterization of single-layer graphene formed on the surface of epitaxial FeRh thin films. The magnetic state of the FeRh surface can be controlled by temperature, magnetic field or strain due to interconnected order parameters. Characterization of graphene layers by X-ray Photoemission and X-ray Absorption Spectroscopy, Low-Energy Ion Scattering, Scanning Tunneling Microscopy, and Low-Energy Electron Microscopy shows that graphene is single-layer, polycrystalline and covers more than 97% of the substrate. Graphene displays several preferential orientations on the FeRh(001) surface with unit vectors of graphene rotated by 30{deg}, 15{deg}, 11{deg}, and 19{deg} with respect to FeRh substrate unit vectors. In addition, the graphene layer is capable to protect the films from oxidation when exposed to air for several months. Therefore, it can be also used as a protective layer during fabrication of magnetic elements or as an atomically thin spacer, which enables incorporation of switchable magnetic layers within stacks of 2D materials in advanced devices.
The epitaxial deposition of the first oxide buffer layer (seed layer) on biaxially textured Ni tape for coated conductors is a critical step that is dependent on the atomistic surface condition of the metal. We present a study of the {100}<100> biaxi
ally textured Ni (001) surface and seed-layer growth using in situ reflection high-energy electron diffraction (RHEED) and Auger electron spectroscopy (AES). Our observations are consistent with formation of a c(2 x 2) 2-D superstructure due to surface segregation of sulfur contained in the metal. We show that this superstructure can have a dramatic effect on the heteroepitaxial growth of oxide seed layers. In particular, the surface superstructure promotes the (200) epitaxial oxide growth of Y2O3-stabilized ZrO2 (YSZ), which is necessary for the development of high-Jc superconducting films for coated conductors.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
