This paper is the third in the series on the technology development for the EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer) mission concept, which in 2011 was selected by NASAs Explorer program for technology development (Category
III). EXCEDE is a 0.7m space telescope concept designed to achieve raw contrasts of 1e6 at an inner working angle of 1.2 l/D and 1e7 at 2 l/D and beyond. This will allow it to directly detect and spatially resolve low surface brightness circumstellar debris disks as well as image giant planets as close as in the habitable zones of their host stars. In addition to doing fundamental science on debris disks, EXCEDE will also serve as a technological and scientific precursor for any future exo-Earth imaging mission. EXCEDE uses a Starlight Suppression System (SSS) based on the PIAA coronagraph, enabling aggressive performance. We report on our continuing progress of developing the SSS for EXCEDE, and in particular (a) the reconfiguration of our system into a more flight-like layout, with an upstream deformable mirror and an inverse PIAA system, as well as a LOWFS, and (b) testing this system in a vacuum chamber, including IWA, contrast, and stability performance. The results achieved so far are 2.9e-7 contrast between 1.2-2.0 l/D and 9.7e-8 contrast between 2.0-6.0 l/D in monochromatic light; as well as 1.4e-6 between 2.0-6.0 l/D in a 10% band, all with a PIAA coronagraph operating at an inner working angle of 1.2 l/D. This constitutes better contrast than EXCEDE requirements (in those regions) in monochromatic light, and progress towards requirements in broadband light. Even though this technology development is primarily targeted towards EXCEDE, it is also germane to any exoplanet direct imaging space-based telescopes because of the many challenges common to different coronagraph architectures and mission requirements.
For the technology development of the mission EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer) - a 0.7 m telescope equipped with a Phase-Induced Amplitude Apodization Coronagraph (PIAA-C) and a 2000-element MEMS deformable mirror, c
apable of raw contrasts of 1e-6 at 1.2 lambda/D and 1e-7 above 2 lambda/D - we developed two test benches simulating its key components, one in air, the other in vacuum. To achieve this level of contrast, one of the main goals is to remove low-order aberrations, using a Low-Order WaveFront Sensor (LOWFS). We tested this key component, together with the coronagraph and the wavefront control, in air at NASA Ames Research Center and in vacuum at Lockheed Martin. The LOWFS, controlling tip/tilt modes in real time at 1~kHz, allowed us to reduce the disturbances in air to 1e-3 lambda/D rms, letting us achieve a contrast of 2.8e-7 between 1.2 and 2 lambda/D. Tests are currently being performed to achieve the same or a better level of correction in vacuum. With those results, and by comparing them to simulations, we are able to deduce its performances on different coronagraphs - different sizes of telescopes, inner working angles, contrasts, etc. - and therefore study its contribution beyond EXCEDE.
High-contrast imaging will be a challenge for future ELTs, because their vibrations create low-order aberrations - mostly tip/tilt - that reduce coronagraphic performances at 1.2 lambda/D and above. A Low-Order WaveFront Sensor (LOWFS) is essential t
o measure and control those aberrations. An experiment simulating a starlight suppression system is currently developed at NASA Ames Research Center, and includes a LOWFS controlling tip/tilt modes in real-time at 500 Hz. The LOWFS allowed us to reduce the tip/tilt disturbances to 1e-3 lambda/D rms, enhancing the previous contrast by a decade, to 8e-7 between 1.2 and 2 lambda/D. A Linear Quadratic Gaussian (LQG) controller is currently implemented to improve even more that result by reducing residual vibrations. This testbed is developed for the mission EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer), selected by NASA for technology development, and designed to study the formation, evolution and architectures of exoplanetary systems and characterize circumstellar environments into stellar habitable zones. It is composed of a 0.7 m telescope equipped with a Phase-Induced Amplitude Apodization Coronagraph (PIAA-C) and a 2000-element MEMS deformable mirror, capable of raw contrasts of 1e-6 at 1.2 lambda/D and 1e-7 above 2 lambda/D. Although the testbed simulates space conditions, its LOWFS has the same design than on the SCExAO instrument at Subaru telescope, with whom it shares the same kind of problematic. Experimental results show that a good knowledge of the low-order disturbances is a key asset for high contrast imaging, whether for real-time control or for post processing, both in space and on ground telescopes.
The mission EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer), selected by NASA for technology development, is designed to study the formation, evolution and architectures of exoplanetary systems and characterize circumstellar enviro
nments into stellar habitable zones. It is composed of a 0.7 m telescope equipped with a Phase-Induced Amplitude Apodization Coronagraph (PIAA-C) and a 2000-element MEMS deformable mirror, capable of raw contrasts of 1e-6 at 1.2 lambda/D and 1e-7 above 2 lambda/D. One of the key challenges to achieve those contrasts is to remove low-order aberrations, using a Low-Order WaveFront Sensor (LOWFS). An experiment simulating the starlight suppression system is currently developed at NASA Ames Research Center, and includes a LOWFS controlling tip/tilt modes in real time at 500 Hz. The LOWFS allowed us to reduce the tip/tilt disturbances to 1e-3 lambda/D rms, enhancing the previous contrast by a decade, to 8e-7 between 1.2 and 2 lambda/D. A Linear Quadratic Gaussian (LQG) controller is currently implemented to improve even more that result by reducing residual vibrations. This testbed shows that a good knowledge of the low-order disturbances is a key asset for high contrast imaging, whether for real-time control or for post processing.
