Detection of Potential Transit Signals in 17 Quarters of Kepler Mission Data

We present the results of a search for potential transit signals in the full 17-quarter data set collected during Keplers primary mission that ended on May 11, 2013, due to the on-board failure of a second reaction wheel needed to maintain high precision, fixed, pointing. The search includes a total of 198,646 targets, of which 112,001 were observed in every quarter and 86,645 were observed in a subset of the 17 quarters. We find a total of 12,669 targets that contain at least one signal that meets our detection criteria: periodicity of the signal, a minimum of three transit events, an acceptable signal-to-noise ratio, and four consistency tests that suppress false positives. Each target containing at least one transit-like pulse sequence is searched repeatedly for other signals that meet the detection criteria, indicating a multiple planet system. This multiple planet search adds an additional 7,698 transit-like signatures for a total of 20,367. Comparison of this set of detected signals with a set of known and vetted transiting planet signatures in the Kepler field of view shows that the recovery rate of the search is 90.3%. We review ensemble properties of the detected signals and present various metrics useful in validating these potential planetary signals. We highlight previously undetected planetary candidates, including several small potential planets in the habitable zone of their host stars.

Detection of Potential Transit Signals in Sixteen Quarters of Kepler Mission Data

We present the results of a search for potential transit signals in four years of photometry data acquired by the Kepler Mission. The targets of the search include 111,800 stars which were observed for the entire interval and 85,522 stars which were observed for a subset of the interval. We found that 9,743 targets contained at least one signal consistent with the signature of a transiting or eclipsing object, where the criteria for detection are periodicity of the detected transits, adequate signal-to-noise ratio, and acceptance by a number of tests which reject false positive detections. When targets that had produced a signal were searched repeatedly, an additional 6,542 signals were detected on 3,223 target stars, for a total of 16,285 potential detections. Comparison of the set of detected signals with a set of known and vetted transit events in the Kepler field of view shows that the recovery rate for these signals is 96.9%. The ensemble properties of the detected signals are reviewed.

Detection of Potential Transit Signals in the First Twelve Quarters of Kepler Mission Data

We present the results of a search for potential transit signals in the first three years of photometry data acquired by the Kepler Mission. The targets of the search include 112,321 targets which were observed over the full interval and an additional 79,992 targets which were observed for a subset of the full interval. From this set of targets we find a total of 11,087 targets which contain at least one signal which meets the Kepler detection criteria: those criteria are periodicity of the signal, an acceptable signal-to-noise ratio, and three tests which reject false positives. Each target containing at least one detected signal is then searched repeatedly for additional signals, which represent multi-planet systems of transiting planets. When targets with multiple detections are considered, a total of 18,406 potential transiting planet signals are found in the Kepler Mission dataset. The detected signals are dominated by events with relatively low signal-to-noise ratios and by events with relatively short periods. The distribution of estimated transit depths appears to peak in the range between 20 and 30 parts per million, with a few detections down to fewer than 10 parts per million. The detections exhibit signal-to-noise ratios from 7.1 sigma, which is the lower cut-off for detections, to over 10,000 sigma, and periods ranging from 0.5 days, which is the shortest period searched, to 525 days, which is the upper limit of achievable periods given the length of the data set and the requirement that all detections include at least 3 transits. The detected signals are compared to a set of known transit events in the Kepler field of view, many of which were identified by alternative methods; the comparison shows that the current search recovery rate for targets with known transit events is 98.3%.

Detection of Potential Transit Signals in the First Three Quarters of Kepler Mission Data

We present the results of a search for potential transit signals in the first three quarters of photometry data acquired by the Kepler Mission. The targets of the search include 151,722 stars which were observed over the full interval and an additional 19,132 stars which were observed for only 1 or 2 quarters. From this set of targets we find a total of 5,392 detections which meet the Kepler detection criteria: those criteria are periodicity of the signal, an acceptable signal-to-noise ratio, and a composition test which rejects spurious detections which contain non-physical combinations of events. The detected signals are dominated by events with relatively low signal-to-noise ratio and by events with relatively short periods. The distribution of estimated transit depths appears to peak in the range between 40 and 100 parts per million, with a few detections down to fewer than 10 parts per million. The detected signals are compared to a set of known transit events in the Kepler field of view which were derived by a different method using a longer data interval; the comparison shows that the current search correctly identified 88.1% of the known events. A tabulation of the detected transit signals, examples which illustrate the analysis and detection process, a discussion of future plans and open, potentially fruitful, areas of further research are included.

The Kepler Pixel Response Function

Kepler seeks to detect sequences of transits of Earth-size exoplanets orbiting Solar-like stars. Such transit signals are on the order of 100 ppm. The high photometric precision demanded by Kepler requires detailed knowledge of how the Kepler pixels respond to starlight during a nominal observation. This information is provided by the Kepler pixel response function (PRF), defined as the composite of Keplers optical point spread function, integrated spacecraft pointing jitter during a nominal cadence and other systematic effects. To provide sub-pixel resolution, the PRF is represented as a piecewise-continuous polynomial on a sub-pixel mesh. This continuous representation allows the prediction of a stars flux value on any pixel given the stars pixel position. The advantages and difficulties of this polynomial representation are discussed, including characterization of spatial variation in the PRF and the smoothing of discontinuities between sub-pixel polynomial patches. On-orbit super-resolution measurements of the PRF across the Kepler field of view are described. Two uses of the PRF are presented: the selection of pixels for each star that maximizes the photometric signal to noise ratio for that star, and PRF-fitted centroids which provide robust and accurate stellar positions on the CCD, primarily used for attitude and plate scale tracking. Good knowledge of the PRF has been a critical component for the successful collection of high-precision photometry by Kepler.