Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userStrong influence of boron precursor powder on the critical current density of MgB2
78
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The influence of the nature of the boron precursor on the superconducting properties of polycrystalline MgB2 was studied. Critical current densities for the MgB2 made from high purity amorphous boron are at least a factor of three higher than typical values measured for standard MgB2 samples made from amorphous precursors. Two possible mechanisms are proposed to account for this difference. Samples made from crystalline boron powders have around an order of magnitude lower Jc compared to those made from amorphous precursors. X-ray, Tc and resistivity studies indicate that this is as a result of reduced current cross section due to the formation of Mg-B-O phases. The samples made from amorphous B contain far fewer Mg-B-O phases than crystalline B despite the fact that the amorphous B contains more B2O3. The different reactivity rates of the precursor powders accounts for this anomaly.
rate research
Read More
The effect of the quality of starting powders on the microstructure and superconducting properties of in-situ processed Fe-sheathed MgB2 tapes has been investigated. Three different types of commercial atomized spherical magnesium powder and two different purities of amorphous boron powder were employed. When using the 10-micrometre magnesium as precursor powders, the Mg reacted with boron more uniformly and quickly, thus the uniformity of the fabricated MgB2 was improved and the grain size of the MgB2 was decreased, hence significant critical current density (Jc) enhancements were achieved for MgB2 tapes. Jc at 4.2 K for MgB2 tapes made from the 10 um Mg and high purity boron powders was at least a factor of ten higher than values measured for MgB2 samples made from all other starting powders. At 20 K, 5 T, the typical Jc values of the tapes were over 1.0x10^4 A/cm^2 and were much better than those of tape samples reported recently.
The DC magnetization and AC complex magnetic susceptibilities were measured for MgB2 single crystals, unsubstituted and carbon substituted with the composition of Mg(B_0.94C_0.06)2. The measurements were performed in AC and DC magnetic fields oriented parallel to the c-axis of the crystals. From the DC magnetization loops and the AC susceptibility measurements, critical current densities (Jc) were derived as a function of temperature and the DC and AC magnetic fields. Results show that the substitution with carbon decreases Jc at low magnetic fields, opposite to the well known effect of an increase of Jc at higher fields. AC magnetic losses were derived from the AC susceptibility data as a function of amplitude and the DC bias magnetic field. The AC losses were determined for temperatures of 0.6 and 0.7 of the transition temperature Tc, so close to the boiling points of LH2 and LNe, potential cooling media for magnesium diboride based composites. The results are analyzed and discussed in the context of the critical state model.
The high resistivity of many bulk and film samples of MgB2 is most readily explained by the suggestion that only a fraction of the cross-sectional area of the samples is effectively carrying current. Hence the supercurrent (Jc) in such samples will be limited by the same area factor, arising for example from porosity or from insulating oxides present at the grain boundaries. We suggest that a correlation should exist, Jc ~ 1/{Rho(300K) - Rho(50K)}, where Rho(300K) - Rho(50K) is the change in the apparent resistivity from 300 K to 50 K. We report measurements of Rho(T) and Jc for a number of films made by hybrid physical-chemical vapor deposition which demonstrate this correlation, although the reduced effective area argument alone is not sufficient. We suggest that this argument can also apply to many polycrystalline bulk and wire samples of MgB2.
Two sets of MgB2 samples doped with up to 5 at. % of Al were prepared in different laboratories using different procedures. Decreases in the a and c lattice parameters were observed with Al doping confirming Al substitution onto the Mg site. The critical temperature (Tc) remained largely unchanged with Al doping. For 1 - 2.5 at.% doping, at 20K the in-field critical current densities (Jcs) were enhanced, particularly at lower fields. At 5K, in-field Jc was markedly improved, e.g. at 5T Jc was enhanced by a factor of 20 for a doping level of 1 at.% Al. The improved Jcs correlate with increased sample resistivity indicative of an increase in the upper critical field, Hc2, through alloying.
We report dc transport and magnetization measurements of Jc in MgB2 wires fabricated by the powder-in-tube method, using commercial MgB2 powder with 5 %at Mg powder added as an additional source of magnesium, and stainless steel as sheath material. By appropriate heat treatments, we have been able to increase Jc by more than one order of magnitude from that of the as-drawn wire. We show that one beneficial effect of the annealing is the elimination of most of the micro-cracks, and we correlate the increase in Jc with the disappearance of the weak-link-type behavior.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
