Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userCoated conductors containing grains with big aspect ratios
89
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
It is shown that the critical currents of high-Tc superconducting tapes fabricated by the coated conductor technologies are enhanced considerably if grain arrangements with large effective grain boundary areas are used. Increasing the aspect ratios of the grains reduces the deleterious effects of the grain boundaries. A practical road to competitive high-Tc cables is proposed.
rate research
Read More
The critical currents of MOD/RABiTS and PLD/IBAD coated conductors have been measured as a function of magnetic field orientation and compared to films grown on single crystal substrates. By varying the orientation of magnetic field applied in the plane of the film, we are able to determine the extent to which current flow in each type of conductor is percolative. Standard MOD/RABiTS conductors have also been compared to samples whose grain boundaries have been doped by diffusing Ca from an overlayer. We find that undoped MOD/RABiTS tapes have a less anisotropic in-plane field dependence than PLD/IBAD tapes and that the uniformity of critical current as a function of in-plane field angle is greater for MOD/RABiTS samples doped with Ca.
Demanding microwave applications in a magnetic field require the material optimization not only in zero-field but, more important, in the in-field flux motion dominated regime. However, the effect of artificial pinning centers (APC) remains unclear at high frequency. Moreover, in coated conductors the evaluation of the high frequency material properties is difficult due to the complicated electromagnetic problem of a thin superconducting film on a buffered metal substrate. In this paper we present an experimental study at 48 GHz of 150-200 nm YBa$_2$Cu$_3$O$_{7-x}$ coated conductors, with and without APCs, on buffered Ni-5at%W tapes. By properly addressing the electromagnetic problem of the extraction of the superconductor parameters from the measured overall surface impedance $Z$, we are able to extract and to comment on the London penetration depth, the flux flow resistivity and the pinning constant, highlighting the effect of artificial pinning centers in these samples.
We present a comparative study of the angular dependent critical current density in YBa2Cu3O7 films deposited on IBAD MgO and on single crystal MgO and SrTiO3 substrates. We identify three angular regimes where pinning is dominated by different types of correlated and uncorrelated defects. We show that those regimes are present in all cases, indicating that the pinning mechanisms are the same, but their extension and characteristics are sample dependent, reflecting the quantitative differences in texture and defect density. In particular, the more defective nature of the films on IBAD turns into an advantage as it results in stronger vortex pinning, demonstrating that the critical current density of the films on single crystals is not an upper limit for the performance of the IBAD coated conductors.
There are numerous potential applications for superconducting tapes, based on YBa2Cu3O7-x (YBCO) films coated onto metallic substrates. A long established goal of more than 15 years has been to understand the magnetic flux pinning mechanisms which allow films to maintain high current densities out to high magnetic fields. In fact, films carry 1-2 orders of magnitude higher current densities than any other form of the material. For this reason, the idea of further improving pinning has received little attention. Now that commercialisation of conductors is much closer, for both better performance and lower fabrication costs, an important goal is to achieve enhanced pinning in a practical way. In this work, we demonstrate a simple and industrially scaleable route which yields a 1.5 to 5-fold improvement in the in-field current densities of already-high-quality conductors.
We report a detailed study performed on La2Zr2O7 (LZO) pyrochlore material grown by Metal-Organic Decomposition (MOD) method as buffer layers for YBa2Cu3O7-x (YBCO) coated conductors. High quality epitaxial LZO thin films have been obtained on single crystal (SC) and Ni-5%at.W substrates. In order to evaluate structural and morphological properties, films have been characterized by means of X-ray diffraction analyses (XRD), atomic force microscope (AFM) and scanning electron microscope (SEM). Precursors solutions and heat treatments have been studied by thermogravimetric analyses (TG-DTA-DTG) and infrared spectra (FT-IR) with the aim of optimizing the annealing process. Thin films of YBCO have been deposited by pulsed laser ablation (PLD) on this buffer layers. The best results obtained on SC showed YBCO films with critical temperature values above 90 K, high self field critical current density values (Jc > 1 MA/cm2) and high irreversibility field values (8.3 T) at 77 K together with a rather high depinning frequency vp (0.5 T, 77 K)>44 GHz as determined at microwaves. The best results on Ni-5%at.W has been obtained introducing in the heat treatment a pyrolysis process at low temperature in air in order to remove the residual organic part of the precursor solution.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
