Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userLinear voltage recovery after a breakdown in a pulsed dc system
94
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Breakdowns may occur in high-voltage applications even in ultrahigh vacuum conditions. Previously, we showed that it is important to pay attention to the post-breakdown voltage recovery in order to limit the appearance of secondary breakdowns associated with the primary ones. This can improve the overall efficiency of the high-voltage device. In this study, we focus on the optimization of the linear post-breakdown voltage recovery, with the principle aim of alleviating the problem of the secondary breakdowns. We investigate voltage recovery scenarios with different starting voltages and slopes of linear voltage increase by using a pulsed dc system. We find that a higher number of pulses during the voltage recovery produces fewer secondary BDs and a lower overall breakdown rate. Lowering the number of pulses led to more dramatic voltage recovery resulting in higher breakdown rates. A steeper voltage increase rate lead to a more localized occurrence of the secondary breakdowns near the end of the voltage recovery period. It was also found that the peak BD probability is regularly observed around 1 s after the end of the ramping period and that its value decreases exponentially with the amount of energy put into the system during the ramping. The value also decays exponentially with a half-life of (1.4$pm$0.3) ms if the voltage only increased between the voltage recovery steps.
rate research
Read More
A superconducting quantum interference device with differential output or DSQUID was proposed earlier for operation in the presence of large common-mode signals. The DSQUID is the differential connection of two identical SQUIDs. Here we show that besides suppression of electromagnetic interference this device provides effective linearization of DC SQUID voltage response. In the frame of the resistive shunted junction model with zero capacitance, we demonstrate that Spur-Free Dynamic Range (SFDR) of DSQUID magnetic flux-to-voltage transfer function is higher than SFDR > 100 dB while Total Harmonic Distortion (THD) of a signal is less than THD < $10^{-3}%$ with a peak-to-peak amplitude of a signal being a quarter of half flux quantum, $2Phi_a = Phi_0/8$. Analysis of DSQUID voltage response stability to a variation of the circuit parameters shows that DSQUID implementation allows doing highly linear magnetic flux-to-voltage transformation at the cost of a high identity of Josephson junctions and high-precision current supply.
Direct current (DC) converters play an essential role in electronic circuits. Conventional high-efficiency DC voltage converters, especially step-up type, rely on switch-mode operation, where energy is periodically stored within and released from inductors and/or capacitors connected in a variety of circuit topologies. However, since these energy storage components, especially inductors, are difficult to scale down, miniaturization of switching converters for on-chip or in-package electronics faces fundamental challenges. Furthermore, the resulting switching currents produce electromagnetic noise, which can cause interference problems in nearby circuits, and even acoustic noise and mechanical vibrations that deteriorate the environment. In order to overcome the limitations of switch-mode converters, photonic transformers, where voltage conversion is achieved through the use of light emission and detection processes, have been demonstrated. However, the demonstrated efficiency is significantly below that of the switch-mode converter. Here we perform a theoretical analysis based on detailed balance, which shows that with a monolithically integrated design that enables efficient photon transport, the photonic transformer can operate with a near-unity conversion efficiency and high voltage conversion ratio. We validate the theoretical analysis with an experiment on a transformer constructed with off-the-shelf discrete components. Our experiment showcases near noiseless operation, as well as a voltage conversion ratio that is significantly higher than obtained in previous photonic transformer works. Our finding points to a high-performance optical solution to miniaturizing DC power converters for electronics and improving the electromagnetic compatibility and quality of electrical power.
Spin accumulation voltages in a non-degenerate Si spin valve are discussed quantitatively as a function of electric bias current using systematic experiments and model calculations. As an open question in semiconductor spintronics, the origin of the deviation of spin accumulation voltages measured experimentally in a non-degenerate Si spin valve is clarified from that obtained by model calculation using the spin drift diffusion equation including the effect of the spin-dependent interfacial resistance of tunneling barriers. Unlike the case of metallic spin valves, the bias dependence of the resistance-area product for a ferromagnet/MgO/Si interface, resulting in the reappearance of the conductance mismatch, plays a central role to induce the deviation.
Fundamental electronic processes such as charge-carrier transport and recombination play a critical role in determining the efficiency of hybrid perovskite solar cells. The presence of mobile ions complicates the development of a clear understanding of these processes as the ions may introduce exceptional phenomena such as hysteresis or giant dielectric constants. As a result, the electronic landscape, including its interaction with mobile ions, is difficult to access both experimentally and analytically. To address this challenge, we applied a series of small perturbation techniques including impedance spectroscopy (IS), intensity-modulated photocurrent spectroscopy (IMPS) and intensity-modulated photovoltage spectroscopy (IMVS) to planar $mathrm{MAPbI_3}$ perovskite solar cells. Our measurements indicate that both electronic as well as ionic responses can be observed in all three methods and assigned by literature comparison. The results reveal that the dominant charge-carrier loss mechanism is surface recombination by limitation of the quasi-Fermi level splitting. The interaction between mobile ions and the electronic charge carriers leads to a shift of the apparent diode ideality factor from 0.74 to 1.64 for increasing illumination intensity, despite the recombination mechanism remaining unchanged.
Experiments in organic semiconductors (polyacenes) evidence a strong super quadratic increase of the current-voltage (I-V) characteristic at voltages in the transition region between linear (Ohmic) and quadratic (trap free space-charge-limited-current) behaviours. Similarly, excess noise measurements at a given frequency and increasing voltages evidence a sharp peak of the relative spectral density of the current noise in concomitance with the strong super-quadratic I-V characteristics. Here we discuss the physical interpretation of these experiments in terms of an essential contribution from field assisted trapping-detrapping processes of injected carriers. To this purpose, the fraction of filled traps determined by the I-V characteristics is used to evaluate the excess noise in the trap filled transition (TFT) regime. We have found an excellent agreement between the predictions of our model and existing experimental results in tetracene and pentacene thin films of different length in the range $0.65 div 35 mu m$.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
