Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userHigh Performance Printed AgO-Zn Rechargeable Battery for Flexible Electronics
86
0
0.0
(
0
)
Authors
Lu Yin
Ask ChatGPT about the research
No Arabic abstract
The rise of flexible electronics calls for cost-effective and scalable batteries with good mechanical and electrochemical performance. In this work, we developed printable, polymer-based AgO-Zn batteries that feature flexibility, rechargeability, high areal capacity, and low impedance. Using elastomeric substrate and binders, the current collectors, electrodes, and separators can be easily screen-printed layer-by-layer and vacuum-sealed in a stacked configuration. The batteries are customizable in sizes and capacities, with the highest obtained areal capacity of 54 mAh/cm2 for primary applications. Advanced micro-CT and EIS were used to characterize the battery, whose mechanical stability was tested with repeated twisting and bending. The batteries were used to power a flexible E-ink display system that requires a high-current drain and exhibited superior performance than commercial coin-cell batteries. The developed battery presents a practical solution for powering a wide range of electronics and holds major implications for the future development of practical and high-performance flexible batteries.
rate research
Read More
Controlling nanostructure from molecular, crystal lattice to the electrode level remains as arts in practice, where nucleation and growth of the crystals still require more fundamental understanding and precise control to shape the microstructure of metal deposits and their properties. This is vital to achieve dendrite-free Li metal anodes with high electrochemical reversibility for practical high-energy rechargeable Li batteries. Here, cryogenic-transmission electron microscopy was used to capture the dynamic growth and atomic structure of Li metal deposits at the early nucleation stage, in which a phase transition from amorphous, disordered states to a crystalline, ordered one was revealed as a function of current density and deposition time. The real-time atomic interaction over wide spatial and temporal scales was depicted by the reactive-molecular dynamics simulations. The results show that the condensation accompanied with the amorphous-to-crystalline phase transition requires sufficient exergy, mobility and time to carry out, contrary to what the classical nucleation theory predicts. These variabilities give rise to different kinetic pathways and temporal evolutions, resulting in various degrees of order and disorder nanostructure in nano-sized domains that dominate in the morphological evolution and reversibility of Li metal electrode. Compared to crystalline Li, amorphous/glassy Li outperforms in cycle life in high-energy rechargeable batteries and is the desired structure to achieve high kinetic stability for long cycle life.
This work reports flexible fully transparent high-voltage diodes that feature high rectification ratio (Rr 10 8) and high breakdown voltage (Vb 150 V) simultaneously, combined with their applications as building blocks of energy management systems in wearable electronics where triboelectric nanogenerators (TENGs) are used as power source. Both experimental results and technology computer aided design (TCAD) simulations suggest that Rr and Vb can be modulated by the offset length in an opposite tendency. The low reverse leakage current (fA/MICRON) guarantees an ultra-low power consumption in standby mode, which is a core issue in wearable device applications. Besides the unprecedented electrical performance, the diodes exhibit good mechanical robustness with minimal degradation throughout the strain and fatigue tests. By incorporating these high-voltage diodes into half-wave and full-wave rectifier circuits, the high alternating current (AC) output voltage of TENGs is successfully rectified into direct current (DC) voltage and charged into supercapacitors (SCs), indicating their high integration and compatibility with TENGs, and thus their promising applications in various wearable electronic systems.
Compton scattering is one of the promising probe to quantitate of the Li under in-operando condition, since high-energy X-rays which have high penetration power into the materials are used as incident beam and Compton scattered energy spectrum have specific line-shape by the elements. We develop in-operando quantitation method of Li composition in the electrodes by using line-shape (Sparameter) analysis of Compton scattered energy spectrum. In this study, we apply S-parameter analysis to commercial coin cell Li-ion rechargeable battery and obtain the variation of S-parameters during charge/discharge cycle at positive and negative electrodes. By using calibration curves for Li composition in the electrodes, we determine the change of Li composition of positive and negative electrodes through S-parameters, simultaneously.
Diodes made of heterostructures of the 2D material graphene and conventional 3D materials are reviewed in this manuscript. Several applications in high frequency electronics and optoelectronics are highlighted. In particular, advantages of metal-insulator-graphene (MIG) diodes over conventional metal-insulator-metal diodes are discussed with respect to relevant figures-of-merit. The MIG concept is extended to 1D diodes. Several experimentally implemented radio frequency circuit applications with MIG diodes as active elements are presented. Furthermore, graphene-silicon Schottky diodes as well as MIG diodes are reviewed in terms of their potential for photodetection. Here, graphene-based diodes have the potential to outperform conventional photodetectors in several key figures-of-merit, such as overall responsivity or dark current levels. Obviously, advantages in some areas may come at the cost of disadvantages in others, so that 2D/3D diodes need to be tailored in application-specific ways.
The use of natural or bioinspired materials to develop edible electronic devices is a potentially disruptive technology that can boost point-of-care testing. The technology exploits devices which can be safely ingested, along with pills or even food, and operated from within the gastrointestinal tract. Ingestible electronics could potentially target a significant number of biomedical applications, both as therapeutic and diagnostic tool, and this technology may also impact the food industry, by providing ingestible or food-compatible electronic tags that can smart track goods and monitor their quality along the distribution chain. We hereby propose temporary tattoo-paper as a simple and versatile platform for the integration of electronics onto food and pharmaceutical capsules. In particular, we demonstrate the fabrication of all-printed Organic Field-Effect Transistors (OFETs) on untreated commercial tattoo-paper, and their subsequent transfer and operation on edible substrates with a complex non-planar geometry.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
