Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userOptimum Multi-Antenna Ambient Backscatter Receiver for General Binary-Modulated Signal
257
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Ambient backscatter communication (AmBC) is becoming increasingly popular for enabling green communication amidst the continual development of the Internet-of-things paradigm. Efforts have been put into backscatter signal detection as the detection performance is limited by the low signal-to-interference-plus-noise ratio (SINR) of the signal at the receiver. The low SINR can be improved by adopting a multi-antenna receiver. In this paper, the optimum multi-antenna receiver that does not impose any constraints on the types of binary modulation performed by the backscatter device and the waveform used by the ambient source system is studied. The proposed receiver owns a simple structure formed by two beamformers. Bit error rate (BER) performances of the optimum receiver are derived under constant-amplitude ambient signal and Gaussian-distributed ambient signal. Moreover, to facilitate the implementation of the optimum receiver, a simplified receiver is proposed and practical approximations to required beamformers are provided. The derived optimum receiver avoids the complex direct path interference cancellation and coherent reception, but exploits the fact that backscatter signal changes the composite channel impinging at the receiver and the directivity of receiver antenna array. Comparative simulation results show that the performance of the optimum receiver achieves the same performance as the coherent receiver even though it realizes non-coherent reception. The studied receivers provide high flexibility for implementing simple and low-cost receivers in different AmBC systems.
rate research
Read More
Ambient Backscatter Communication (AmBC) is an emerging communication technology that can enable green Internet-of-Things deployments. The widespread acceptance of this paradigm is limited by low Signal-to-Interference-Plus-Noise Ratio (SINR) of the signal impinging on the receiver antenna due to the strong direct path interference and unknown ambient signal. The adverse impact of these two factors can be mitigated by using non-coherent multi-antenna receivers, which is known to require higher SINR to reach Bit-Error-Rate (BER) performance of coherent receivers. However, in literature, coherent receivers for AmBC systems are little-studied because of unknown ambient signal, unknown location of AmBC tags, and varying channel conditions. In this paper, a coherent multi-antenna receiver, which does not require a prior information of the ambient signal, for decoding Binary-Phase-shift-Keying (BPSK) modulated signal is presented. The performance of the proposed receiver is compared with the ideal coherent receiver that has a perfect phase information, and also with the performance of non-coherent receiver, which assumes distributions for ambient signal and phase offset caused by excess length of the backscatter path. Comparative simulation results show the designed receiver can achieve the same BER-performance of the ideal coherent receiver with 1-dB more SINR, which corresponds to 5-dB or more gain with respect to non-coherent reception of On-Off-Keying modulated signals. Variation of the detection performance with the tag location shows that the coverage area is in the close vicinity of the transmitter and a larger region around the receiver, which is consistent with the theoretical results.
Existing tag signal detection algorithms inevitably suffer from a high bit error rate (BER) due to the difficulties in estimating the channel state information (CSI). To eliminate the requirement of channel estimation and to improve the system performance, in this paper, we adopt a deep transfer learning (DTL) approach to implicitly extract the features of communication channel and directly recover tag symbols. Inspired by the powerful capability of convolutional neural networks (CNN) in exploring the features of data in a matrix form, we design a novel covariance matrix aware neural network (CMNet)-based detection scheme to facilitate DTL for tag signal detection, which consists of offline learning, transfer learning, and online detection. Specifically, a CMNet-based likelihood ratio test (CMNet-LRT) is derived based on the minimum error probability (MEP) criterion. Taking advantage of the outstanding performance of DTL in transferring knowledge with only a few training data, the proposed scheme can adaptively fine-tune the detector for different channel environments to further improve the detection performance. Finally, extensive simulation results demonstrate that the BER performance of the proposed method is comparable to that of the optimal detection method with perfect CSI.
Ambient backscatter communications is an emerging paradigm and a key enabler for pervasive connectivity of low-powered wireless devices. It is primarily beneficial in the Internet of things (IoT) and the situations where computing and connectivity capabilities expand to sensors and miniature devices that exchange data on a low power budget. The premise of the ambient backscatter communication is to build a network of devices capable of operating in a battery-free manner by means of smart networking, radio frequency (RF) energy harvesting and power management at the granularity of individual bits and instructions. Due to this innovation in communication methods, it is essential to investigate the performance of these devices under practical constraints. To do so, this article formulates a model for wireless-powered ambient backscatter devices and derives a closed-form expression of outage probability under Rayleigh fading. Based on this expression, the article provides the power-splitting factor that balances the tradeoff between energy harvesting and achievable data rate. Our results also shed light on the complex interplay of a power-splitting factor, amount of harvested energy, and the achievable data rates.
Ambient backscatter communication (AmBC) leverages the existing ambient radio frequency (RF) environment to implement communication with battery-free devices. The key challenge in the development of AmBC is the very weak RF signals backscattered by the AmBC Tag. To overcome this challenge, we propose the use of orthogonal space-time block codes (OSTBC) by incorporating multiple antennas at the Tag as well as at the Reader. Our approach considers both coherent and non-coherent OSTBC so that systems with and without channel state information can be considered. To allow the application of OSTBC, we develop an approximate linearized and normalized multiple-input multiple-output (MIMO) channel model for the AmBC system. This MIMO channel model is shown to be accurate for a wide range of useful operating conditions. Two coherent detectors and a non-coherent detector are also provided based on the proposed AmBC channel model. Simulation results show that enhanced bit error rate performance can be achieved, demonstrating the benefit of using multiple antennas at the Tag as well as the Reader.
Beamforming has great potential for joint communication and sensing (JCAS), which is becoming a demanding feature on many emerging platforms such as unmanned aerial vehicles and smart cars. Although beamforming has been extensively studied for communication and radar sensing respectively, its application in the joint system is not straightforward due to different beamforming requirements by communication and sensing. In this paper, we propose a novel multibeam framework using steerable analog antenna arrays, which allows seamless integration of communication and sensing. Different to conventional JCAS schemes that support JCAS using a single beam, our framework is based on the key innovation of multibeam technology: providing fixed subbeam for communication and packet-varying scanning subbeam for sensing, simultaneously from a single transmitting array. We provide a system architecture and protocols for the proposed framework, complying well with modern packet communication systems with multicarrier modulation. We also propose low-complexity and effective multibeam design and generation methods, which offer great flexibility in meeting different communication and sensing requirements. We further develop sensing parameter estimation algorithms using conventional digital Fourier transform and 1D compressive sensing techniques, matching well with the multibeam framework. Simulation results are provided and validate the effectiveness of our proposed framework, beamforming design methods and the sensing algorithms.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
