Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userAnalysis of Magnetic Vortex Dissipation in Sn-Segregated Boundaries in Nb$_3$Sn Superconducting RF Cavities
247
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We study mechanisms of vortex nucleation in Nb$_3$Sn Superconducting RF (SRF) cavities using a combination of experimental, theoretical, and computational methods. Scanning transmission electron microscopy (STEM) image and energy dispersive spectroscopy (EDS) of some Nb$_3$Sn cavities show Sn segregation at grain boundaries in Nb$_3$Sn with Sn concentration as high as $sim$35 at.% and widths $sim$3 nm in chemical composition. Using ab initio calculations, we estimate the effect excess tin has on the local superconducting properties of the material. We model Sn segregation as a lowering of the local critical temperature. We then use time-dependent Ginzburg-Landau theory to understand the role of segregation on magnetic vortex nucleation. Our simulations indicate that the grain boundaries act as both nucleation sites for vortex penetration and pinning sites for vortices after nucleation. Depending on the magnitude of the applied field, vortices may remain pinned in the grain boundary or penetrate the grain itself. We estimate the superconducting losses due to vortices filling grain boundaries and compare with observed performance degradation with higher magnetic fields. We estimate that the quality factor may decrease by an order of magnitude ($10^{10}$ to $10^9$) at typical operating fields if 0.03% of the grain boundaries actively nucleate vortices. We additionally estimate the volume that would need to be filled with vortices to match experimental observations of cavity heating.
rate research
Read More
The high frequency vortex motion in Nb$_3$Sn was analyzed in this work up to 12 T. We used a dielectric loaded resonator tuned at 15 GHz to evaluate the surface impedance $Z$ of a Nb$_3$Sn bulk sample (24.8 at.%Sn). From the field induced variation of $Z$, the high frequency vortex parameters (the pinning constant $k_p$, the depinning frequency $ u_p$ and the flux flow resistivity $rho_{ff}$) were obtained over a large temperature and field range; their field and temperature dependence were analyzed. Comparison with other superconducting materials shows that high frequency applications in strong magnetic fields are also feasible with Nb$_3$Sn. In the present work, we report the first measurements about the microwave response in Nb$_3$Sn in strong magnetic fields.
Nb$_3$Sn is currently the most promising material other than niobium for future superconducting radiofrequency cavities. Critical fields above 120 mT in pulsed operation and about 80 mT in CW have been achieved in cavity tests. This is large compared to the lower critical field as derived from the London penetration depth, extracted from low field surface impedance measurements. In this paper direct measurements of the London penetration depth from which the lower critical field and the superheating field are derived are presented. The field of first vortex penetration is measured under DC and RF fields. The combined results confirm that Nb$_3$Sn cavities are indeed operated in a metastable state above the lower critical field but are currently limited to a critical field well below the superheating field.
Point contact tunneling (PCT) spectroscopy measurements are reported over wide areas of cm-sized cut outs from niobium superconducting RF cavities. A comparison is made between a high-quality, conventionally processed (CP) cavity with a high field Q drop for acceleration field E $>$ 20 MV/m and a nitrogen doped (N-doped) cavity that exhibits an increasing Q up to fields approaching 15 MV/m. The CP cavity displays hot spot regions at high RF fields where Q-drop occurs as well as unaffected regions (cold spots). PCT data on cold spots reveals a near ideal BCS density of states (DOS) with gap parameters, $Delta$ as high as 1.62 meV, that are among the highest values ever reported for Nb. Hot spot regions exhibit a wide distribution of gap values down to $Delta sim$ 1.0 meV and DOS broadening characterized by a relatively large value of pair-breaking rate, $Gamma$, indicating surface regions of significantly reduced superconductivity. In addition, hot spots commonly exhibit Kondo tunneling peaks indicative of surface magnetic moments attributed to a defective oxide. N-doped cavities reveal a more homoegeneous gap distribution centered at $Delta sim$ 1.5 meV and relatively small values of $Gamma/Delta$. The absence of regions of significantly reduced superconductivity indicates that the N interstitials are playing an important role in preventing the formation of hydride phases and other macroscopic defects which might otherwise severely affect the local, surface superconductivity that lead to hot spot formation. The N-doped cavities also display a significantly improved surface oxide, i.e., increased thickness and tunnel barrier height, compared to CP cavities. These results help explain the improved performance of N-doped cavities and give insights into the origin of the initial increasing Q with RF amplitude.
A major focus of Nb$_3$Sn accelerator magnets is on significantly reducing or eliminating their training. Demonstration of an approach to increase the $C_p$ of Nb$_3$Sn magnets using new materials and technologies is very important both for particle accelerators and light sources. It would improve thermal stability and lead to much shorter magnet training, with substantial savings in machines commissioning costs. Both Hypertech and Bruker-OST have attempted to introduce high-$C_p$ elements in their wire design. This paper includes a description of these advanced wires, the finite element model of their heat diffusion properties as compared with the standard wires, and whenever available, a comparison between the minimum quench energy (MQE) calculated by the model and actual MQE measurements on wires.
We report a systematic study on the growth conditions of Sn$_{1-x}$In$_x$Te thin films by molecular beam epitaxy for maximization of superconducting transition temperature $T_mathrm{c}$. Careful tuning of the flux ratios of Sn, In, and Te enables us to find an optimum condition for substituting rich In content ($x$ = 0.66) into Sn site in a single phase of Sn$_{1-x}$In$_x$Te beyond the bulk solubility limit at ambient pressure ($x$ = 0.5). $T_mathrm{c}$ shows a dome-shaped dependence on In content $x$ with the highest $T_mathrm{c}$ = 4.20 K at $x$ = 0.55, being consistent to that reported for bulk crystals. The well-regulated Sn$_{1-x}$In$_x$Te films can be a useful platform to study possible topological superconductivity by integrating them into the state-of-the-art junctions and/or proximity-coupled devices.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
