Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMulti-GMR sensors controlled by additive dipolar coupling
150
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Vertical packaging of multiple Giant Magnetoresistance (multi-GMR) stacks is a very interesting noise reduction strategy for local magnetic sensor measurements, which has not been reported experimentally so far. Here, we have fabricated multi-GMR sensors (up to 12 repetitions) keeping good GMR ratio, linearity and low roughness. From magnetotransport measurements, two different resistance responses have been observed with a crossover around 5 GMR repetitions: step-like (N<5) and linear (N>5) behavior, respectively. With the help of micromagnetic simulations, we have analyzed in detail the two main magnetic mechanisms: the Neel coupling distribution induced by the roughness propagation and the additive dipolar coupling between the N free layers. Furthermore we have correlated the dipolar coupling mechanism, controlled by the number of GMRs (N) and lateral dimensions (width), to the sensor performance (sensitivity, noise and detectivity) in good agreement with analytical theory. The noise roughly decreases in multi-GMRs as 1/sqrt{N} in both regimes (low frequency 1/f and thermal noise). The sensitivity is even stronger reduced, scaling as 1/N, in the strong dipolar regime (narrow devices) while converges to a constant value in the weak dipolar regime (wide devices). Very interestingly, they are more robust against undesirable RTN noise than single GMRs at high voltages and the linearity can be extended towards much larger magnetic field range without dealing with the size and the reduction of GMR ratio. Finally, we have identified the optimal conditions for which multi-GMRs exhibit lower magnetic field detectivity than single GMRs: wide devices operating in the thermal regime where much higher voltage can be applied without generating remarkable magnetic noise.
rate research
Read More
We demonstrate a novel concept for operating graphene-based Hall sensors using an alternating current (AC) modulated gate voltage, which provides three important advantages compared to Hall sensors under static operation: 1) The sensor sensitivity can be doubled by utilizing both n- and p-type conductance. 2) A static magnetic field can be read out at frequencies in the kHz range, where the 1/f noise is lower compared to the static case. 3) The off-set voltage in the Hall signal can be reduced. This significantly increases the signal-to-noise ratio compared to Hall sensors without a gate electrode. A minimal detectable magnetic field Bmin down to 290 nT/sqrt(Hz) and sensitivity up to 0.55 V/VT was found for Hall sensors fabricated on flexible foil. This clearly outperforms state-of-the-art flexible Hall sensors and is comparable to the values obtained by the best rigid III/V semiconductor Hall sensors.
The evolution of information technology has been driven by the discovery of new forms of large magnetoresistance (MR), such as giant magnetoresistance (GMR) and tunnelling magnetoresistance (TMR) in magnetic multilayers. Recently, new types of MR have been observed in much simpler bilayers consisting of ferromagnetic (FM)/nonmagnetic (NM) thin films; however, the magnitude of MR in these materials is very small (0.01 ~ 1%). Here, we demonstrate that NM/FM bilayers consisting of a NM InAs quantum well conductive channel and an insulating FM (Ga,Fe)Sb layer exhibit giant proximity magnetoresistance (PMR) (~80% at 14 T). This PMR is two orders of magnitude larger than the MR observed in NM/FM bilayers reported to date, and its magnitude can be controlled by a gate voltage. These results are explained by the penetration of the InAs two-dimensional-electron wavefunction into (Ga,Fe)Sb. The ability to strongly modulate the NM channel current by both electrical and magnetic gating represents a new concept of magnetic-gating spin transistors.
Ultrasound detection is one of the most important nondestructive subsurface characterization tools of materials, whose goal is to laterally resolve the subsurface structure with nanometer or even atomic resolution. In recent years, graphene resonators attracted attention as loudspeaker and ultrasound radio, showing its potential to realize communication systems with air-carried ultrasound. Here we show a graphene resonator that detects ultrasound vibrations propagating through the substrate on which it was fabricated. We achieve ultimately a resolution of $approx7$~pm/$mathrm{sqrt Hz}$ in ultrasound amplitude at frequencies up to 100~MHz. Thanks to an extremely high nonlinearity in the mechanical restoring force, the resonance frequency itself can also be used for ultrasound detection. We observe a shift of 120~kHz at a resonance frequency of 65~MHz for an induced vibration amplitude of 100~pm with a resolution of 25~pm. Remarkably, the nonlinearity also explains the generally observed asymmetry in the resonance frequency tuning of the resonator when pulled upon with an electrostatic gate. This work puts forward a sensor design that fits onto an atomic force microscope cantilever and therefore promises direct ultrasound detection at the nanoscale for nondestructive subsurface characterization.
Solid-state quantum acoustodynamic (QAD) systems provide a compact platform for quantum information storage and processing by coupling acoustic phonon sources with superconducting or spin qubits. The multi-mode composite high-overtone bulk acoustic wave resonator (HBAR) is a popular phonon source well suited for QAD. However, scattering from defects, grain boundaries, and interfacial/surface roughness in the composite transducer severely limits the phonon relaxation time in sputter-deposited devices. Here, we grow an epitaxial-HBAR, consisting of a metallic NbN bottom electrode and a piezoelectric GaN film on a SiC substrate. The acoustic impedance-matched epi-HBAR has a power injection efficiency > 99% from transducer to phonon cavity. The smooth interfaces and low defect density reduce phonon losses, yielding fxQ products and phonon lifetimes up to 1.36 x 10^17 Hz and 500 microseconds respectively. The GaN/NbN/SiC epi-HBAR is an electrically actuated, multi-mode phonon source that can be directly interfaced with NbN-based superconducting qubits or SiC-based spin qubits.
Semiconductors require stable doping for applications in transistors, optoelectronics, and thermoelectrics. However, this has been challenging for two-dimensional (2D) materials, where existing approaches are either incompatible with conventional semiconductor processing or introduce time-dependent, hysteretic behavior. Here we show that low temperature (< 200$^circ$ C) sub-stoichiometric AlO$_x$ provides a stable n-doping layer for monolayer MoS$_2$, compatible with circuit integration. This approach achieves carrier densities > 2x10$^{13}$ 1/cm$^2$, sheet resistance as low as ~7 kOhm/sq, and good contact resistance ~480 Ohm.um in transistors from monolayer MoS$_2$ grown by chemical vapor deposition. We also reach record current density of nearly 700 uA/um (>110 MA/cm$^2$) in this three-atom-thick semiconductor while preserving transistor on/off current ratio > $10^6$. The maximum current is ultimately limited by self-heating and could exceed 1 mA/um with better device heat sinking. With their 0.1 nA/um off-current, such doped MoS$_2$ devices approach several low-power transistor metrics required by the international technology roadmap
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
