Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userPreventing Aluminum Photocorrosion for Ultraviolet Plasmonics
115
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Ultraviolet (UV) plasmonics aims at combining the strong absorption bands of molecules in the UV range with the intense electromagnetic fields of plasmonic nanostructures to promote surface-enhanced spectroscopy and catalysis. Currently, aluminum is the most widely used metal for UV plasmonics, and is generally assumed to be remarkably stable thanks to its natural alumina layer passivating the metal surface. However, we find here that under 266 nm UV illumination, aluminum can undergo a dramatic photocorrosion in water within a few tens of seconds and even at low average UV powers. This aluminum instability in water environments critically limits the UV plasmonics applications. We show that the aluminum photocorrosion is related to the nonlinear absorption by water in the UV range leading to the production of hydroxyl radicals. Different corrosion protection approaches are tested using scavengers for reactive oxygen species and polymer layers deposited on top of the aluminum structures. Using optimized protection, we achieve a ten-fold increase in the available UV power range leading to no visible photocorrosion effects. This technique is crucial to achieve stable use of aluminum nanostructures for UV plasmonics in aqueous solutions.
rate research
Read More
Extending plasmonics into the ultraviolet range imposes the use of aluminum to achieve the best optical performance. However, water corrosion is a major limiting issue for UV aluminum plasmonics, as this phenomenon occurs significantly faster in presence of UV light, even at low laser powers of a few microwatts. Here we assess the performance of nanometer-thick layers of various metal oxides deposited by atomic layer deposition (ALD) and plasma-enhanced chemical vapor deposition (PECVD) on top of aluminum nanoapertures to protect the metal against UV photocorrosion. The combination of a 5 nm Al2O3 layer covered by a 5 nm TiO2 capping provides the best resistance performance, while a single 10 nm layer of SiO2 or HfO2 is a good alternative. We also report the influence of the laser wavelength, the laser operation mode and the pH of the solution. Properly choosing these conditions significantly extends the range of optical powers for which the aluminum nanostructures can be used. As application, we demonstrate the label-free detection of streptavidin proteins with improved signal to noise ratio. Our approach is also beneficial to promote the long-term stability of the aluminum nanostructures. Finding the appropriate nanoscale protection against aluminum corrosion is the key to enable the development of UV plasmonic applications in chemistry and biology.
Plasmonics applications have been extending into the ultraviolet region of the electromagnetic spectrum. Unfortunately the commonly used noble metals have intrinsic optical properties that limit their use above 350 nm. Aluminum is probably the most suitable material for UV plasmonics and in this work we show that nanoporous aluminum can be prepared starting from an alloy of Mg3Al2. The porous metal is obtained by means of a galvanic replacement reaction. Such a nanoporous metal can be exploited to achieve a plasmonic material for enhanced UV Raman spectroscopy and fluorescence. Thanks to the large surface to volume ratio this material represents a powerful platform for promoting interaction between plasmonic substrates and molecules in the UV.
Two-dimensional materials exhibit a fascinating range of electronic and photonic properties vital for nanophotonics, quantum optics and emerging quantum information technologies. Merging concepts from the fields of ab initio materials science and nanophotonics, there is now an opportunity to engineer new photonic materials whose optical, transport, and scattering properties are tailored to attain thermodynamic and quantum limits. Here, we present first-principles calculations predicting that Argentene, a single-crystalline hexagonal close-packed monolayer of Ag, can dramatically surpass the optical properties and electrical conductivity of conventional plasmonic materials. In the low-frequency limit, we show that the scattering rate and resistivity reduce by a factor of three compared to the bulk three-dimensional metal. Most importantly, the low scattering rate extends to optical frequencies in sharp contrast to e.g. graphene, whose scattering rate increase drastically in the near-infrared range due to optical-phonon scattering. Combined with an intrinsically high carrier density, this facilitates highly-confined surface plasmons extending to visible frequencies. We evaluate Argentene across three distinct figures of merit, spanning the spectrum of typical plasmonic applications; in each, Argentene outperforms the state-of-the-art. This unique combination of properties will make Argentene a valuable addition to the two-dimensional heterostructure toolkit for quantum electronic and photonic technologies.
We report on the first beta gallium oxide (beta-Ga2O3) crystal feedback oscillator built by employing a vibrating beta-Ga2O3 nanoresonator as the frequency reference for real-time middle ultraviolet (MUV) light detection. We fabricate suspended beta-Ga2O3 nanodevices through synthesis of beta-Ga2O3 nanoflakes using low-pressure chemical vapor deposition (LPCVD), and dry transfer of nanoflakes on microtrenches. Open-loop tests reveal a resonance of the beta-Ga2O3 device at ~30 MHz. A closed-loop oscillator is then realized by using a combined optical-electrical feedback circuitry, to perform real-time resonant sensing of MUV irradiation. The oscillator exposed to cyclic MUV irradiation exhibits resonant frequency downshifts, with a measured responsivity of $mathscr{R}$ = -3.1 Hz/pW and a minimum detectable power of delta Pmin = 0.53 nW for MUV detection.
In the present investigation, a strongly bonded strip of an aluminium-magnesium based alloy AA5086 is successfully produced through accumulative roll bonding (ARB). A maximum of up to eight passes has been used for the purpose. Microstructural characterization using electron backscatter diffraction (EBSD) technique indicates the formation of submicron sized (~200-300 nm) subgrains inside the layered microstructure. The material is strongly textured where individual layers possess typical FCC rolling texture components. More than three times enhancement in 0.2% proof stress (PS) has been obtained after 8 passes due to grain refinement and strain hardening
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
