Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userHighly sensitive piezotronic pressure sensors based on undoped GaAs nanowire ensembles
165
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Semiconducting piezoelectric materials have attracted considerable interest due to their central role in the emerging field of piezotronics, where the development of a piezo-potential in response to stress or strain can be used to tune the band structure of the semiconductor, and hence its electronic properties. This coupling between piezoelectricity and semiconducting properties can be readily exploited for force or pressure sensing using nanowires, where the geometry and unclamped nature of nanowires render them particularly sensitive to small forces. At the same time, piezoelectricity is known to manifest more strongly in nanowires of certain semiconductors. Here, we report the design and fabrication of highly sensitive piezotronic pressure sensors based on GaAs nanowire ensemble sandwiched between two electrodes in a back-to-back diode configuration. We analyse the current-voltage characteristics of these nanowire-based devices in response to mechanical loading in light of the corresponding changes to the device band structure. We observe a high piezotronic sensitivity to pressure, of ~7800 meV/MPa. We attribute this high sensitivity to the nanowires being fully depleted due to the lack of doping, as well as due to geometrical pressure focusing and current funneling through polar interfaces.
rate research
Read More
The high flexibility, impermeability and strength of graphene membranes are key properties that can enable the next generation of nanomechanical sensors. However, for capacitive pressure sensors the sensitivity offered by a single suspended graphene membrane is too small to compete with commercial sensors. Here, we realize highly sensitive capacitive pressure sensors consisting of arrays of nearly ten thousand small, freestanding double-layer graphene membranes. We fabricate large arrays of small diameter membranes using a procedure that maintains the superior material and mechanical properties of graphene, even after high-temperature anneals. These sensors are readout using a low cost battery-powered circuit board, with a responsivity of up to 47.8 aF Pa$^{-1}$ mm$^{-2}$, thereby outperforming commercial sensors.
We realize squeeze film pressure sensors using suspended, high mechanical quality silicon nitride membranes forming few-micron gap sandwiches. The effects of air pressure on the mechanical vibrations of the membranes are investigated in the range 10^-3-50 mbar and the intermembrane coupling induced by the gas is discussed in light of a squeeze film coupled-oscillator model. The high responsivity (several kHz/mbar) and the sub-pascal sensitivity of such simple pressure sensors are attractive for absolute and direct pressure measurements in rarefied air or high vacuum environments.
We present a design for a piezoelectric-driven uniaxial stress cell suitable for use at ambient and cryogenic temperatures, and that incorporates both a displacement and a force sensor. The cell has a diameter of 46 mm and a height of 13 mm. It can apply a zero-load displacement of up to ~45 $mu$m, and a zero-displacement force of up to ~245 N. With combined knowledge of the displacement and force applied to the sample, it can quickly be determined whether the sample and its mounts remain within their elastic limits. In tests on the oxide metal Sr$_2$RuO$_4$, we found that at room temperature serious plastic deformation of the sample onset at a uniaxial stress of ~0.2 GPa, while at 5 K the sample deformation remained elastic up to almost 2 GPa. This result highlights the usefulness of in situ tuning, in which the force can be applied after cooling samples to cryogenic temperatures.
The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different sensing concepts and give an overview of the relevant material properties, fabrication routes, and device operation principles. Finally, we discuss sensor readout and integration methods and provide comparisons against the state of the art to show both the challenges and promises of 2D material-based nanoelectromechanical sensing.
A highly sensitive refractive index sensor based on grating-assisted strip waveguide directional coupler is proposed. The sensor is designed using two coupled asymmetric strip waveguides with a top-loaded grating structure in one of the waveguides. Maximum light couples from one waveguide to the other at the resonance wavelength, and the change in resonance wavelength with the change in refractive index of the medium in the cover region is a measure of the sensitivity. The proposed sensor would be an on-chip device with a high refractive index sensitivity of ~ 104 nm/RIU, and negligible temperature sensitivity (< 1nm/0C). The sensor configuration offers a low propagation loss, thereby enhancing the sensitivity. Variation of the sensitivity with the waveguide parameters of the proposed sensor have been studied to optimize the design.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
