Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userSqueeze film pressure sensors based on SiN membrane sandwiches
299
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We realize squeeze film pressure sensors using suspended, high mechanical quality silicon nitride membranes forming few-micron gap sandwiches. The effects of air pressure on the mechanical vibrations of the membranes are investigated in the range 10^-3-50 mbar and the intermembrane coupling induced by the gas is discussed in light of a squeeze film coupled-oscillator model. The high responsivity (several kHz/mbar) and the sub-pascal sensitivity of such simple pressure sensors are attractive for absolute and direct pressure measurements in rarefied air or high vacuum environments.
rate research
Read More
The high flexibility, impermeability and strength of graphene membranes are key properties that can enable the next generation of nanomechanical sensors. However, for capacitive pressure sensors the sensitivity offered by a single suspended graphene membrane is too small to compete with commercial sensors. Here, we realize highly sensitive capacitive pressure sensors consisting of arrays of nearly ten thousand small, freestanding double-layer graphene membranes. We fabricate large arrays of small diameter membranes using a procedure that maintains the superior material and mechanical properties of graphene, even after high-temperature anneals. These sensors are readout using a low cost battery-powered circuit board, with a responsivity of up to 47.8 aF Pa$^{-1}$ mm$^{-2}$, thereby outperforming commercial sensors.
The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different sensing concepts and give an overview of the relevant material properties, fabrication routes, and device operation principles. Finally, we discuss sensor readout and integration methods and provide comparisons against the state of the art to show both the challenges and promises of 2D material-based nanoelectromechanical sensing.
We report the development of a scanning force microscope based on an ultra-sensitive silicon nitride membrane transducer. Our development is made possible by inverting the standard microscope geometry - in our instrument, the substrate is vibrating and the scanning tip is at rest. We present first topography images of samples placed on the membrane surface. Our measurements demonstrate that the membrane retains an excellent force sensitivity when loaded with samples and in the presence of a scanning tip. We discuss the prospects and limitations of our instrument as a quantum-limited force sensor and imaging tool.
We demonstrate a novel concept for operating graphene-based Hall sensors using an alternating current (AC) modulated gate voltage, which provides three important advantages compared to Hall sensors under static operation: 1) The sensor sensitivity can be doubled by utilizing both n- and p-type conductance. 2) A static magnetic field can be read out at frequencies in the kHz range, where the 1/f noise is lower compared to the static case. 3) The off-set voltage in the Hall signal can be reduced. This significantly increases the signal-to-noise ratio compared to Hall sensors without a gate electrode. A minimal detectable magnetic field Bmin down to 290 nT/sqrt(Hz) and sensitivity up to 0.55 V/VT was found for Hall sensors fabricated on flexible foil. This clearly outperforms state-of-the-art flexible Hall sensors and is comparable to the values obtained by the best rigid III/V semiconductor Hall sensors.
Semiconducting piezoelectric materials have attracted considerable interest due to their central role in the emerging field of piezotronics, where the development of a piezo-potential in response to stress or strain can be used to tune the band structure of the semiconductor, and hence its electronic properties. This coupling between piezoelectricity and semiconducting properties can be readily exploited for force or pressure sensing using nanowires, where the geometry and unclamped nature of nanowires render them particularly sensitive to small forces. At the same time, piezoelectricity is known to manifest more strongly in nanowires of certain semiconductors. Here, we report the design and fabrication of highly sensitive piezotronic pressure sensors based on GaAs nanowire ensemble sandwiched between two electrodes in a back-to-back diode configuration. We analyse the current-voltage characteristics of these nanowire-based devices in response to mechanical loading in light of the corresponding changes to the device band structure. We observe a high piezotronic sensitivity to pressure, of ~7800 meV/MPa. We attribute this high sensitivity to the nanowires being fully depleted due to the lack of doping, as well as due to geometrical pressure focusing and current funneling through polar interfaces.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
