Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userBand-Gap Control via Structural and Chemical Tuning of Transition Metal Perovskite Chalcogenides
117
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Transition metal perovskite chalcogenides (TMPC) are a new class of semiconductor materials with broad tunability of physical properties due to their chemical and structural flexibility. Theoretical calculations show that band gaps of TMPCs are tunable from Far IR to UV spectrum. Amongst these materials, more than a handful of materials have energy gap and very high absorption coefficients, which are appropriate for optoelectronic applications, especially solar energy conversion. Despite several promising theoretical predictions, very little experimental studies on their physical properties are currently available, especially optical properties. We report a new synthetic route towards high quality bulk ceramic TMPCs and systematic study of three phases, SrZrS3 in two different room temperature stabilized phases and one of BaZrS3. All three materials were synthesized with a catalyzed solid-state reaction process in sealed ampoules. Structural and chemical characterizations establish high quality of the samples, which is confirmed by the intense room temperature photoluminescence (PL) spectra showing direct band gaps around 1.53eV, 2.13eV and 1.81eV respectively. The potential of these materials for solar energy conversion was evaluated by measurement of PL quantum efficiency and estimate of quasi Fermi level splitting.
rate research
Read More
III-VI post-transition metal chalcogenides (InSe and GaSe) are a new class of layered semiconductors, which feature a strong variation of size and type of their band gaps as a function of number of layers (N). Here, we investigate exfoliated layers of InSe and GaSe ranging from bulk crystals down to monolayer, encapsulated in hexagonal boron nitride, using Raman spectroscopy. We present the N-dependence of both intralayer vibrations within each atomic layer, as well as of the interlayer shear and layer breathing modes. A linear chain model can be used to describe the evolution of the peak positions as a function of N, consistent with first principles calculations.
Silicene monolayers grown on Ag(111) surfaces demonstrate a band gap that is tunable by oxygen adatoms from semimetallic to semiconducting type. By using low-temperature scanning tunneling microscopy, it is found that the adsorption configurations and amounts of oxygen adatoms on the silicene surface are critical for band-gap engineering, which is dominated by different buckled structures in R13xR13, 4x4, and 2R3x2R3 silicene layers. The Si-O-Si bonds are the most energy-favored species formed on R13xR13, 4x4, and 2R3x2R3 structures under oxidation, which is verified by in-situ Raman spectroscopy as well as first-principles calculations. The silicene monolayers retain their structures when fully covered by oxygen adatoms. Our work demonstrates the feasibility of tuning the band gap of silicene with oxygen adatoms, which, in turn, expands the base of available two-dimensional electronic materials for devices with properties that is hardly achieved with graphene oxide.
Based on first-principles calculations, we have found a family of two-dimensional (2D) transition-metal chalcogenides MX$_5$ (M = Zr, Hf and X = S, Se and Te) can host quantum spin Hall (QSH) effect. The molecular dynamics (MD) simulation indicate that they are all thermal-dynamically stable at room temperature, the largest band gap is 0.19 eV. We have investigated the electronic and topological properties and they have very similar properties. For the single-layer ZrX$_5$, they are all gapless semimetals without consideration of spin-orbit coupling (SOC). The consideration of SOC will result in insulating phases with band gaps of 49.5 meV (direct), 0.18 eV (direct) and 0.13 eV (indirect) for ZrS$_5$, ZrSe$_5$ to ZrTe$_5$, respectively. The evolution of Wannier charge centers (WCC) and edge states confirm they are all QSH insulators. The mechanisms for QSH effect in ZrX$_5$ originate from the special nonsymmorphic space group features. In addition, the QSH state of ZrS$_5$ survives at a large range of strain as long as the interchain coupling is not strong enough to reverse the band ordering. The single-layer ZrS$_5$ will occur a TI-to-semimetal (metal) or metal-to-semimetal transition under certain strain. The realization of pure MX$_5$ monolayer should be readily obtained via mechanical exfoliation methods, thus holding great promise for nanoscale device applications and stimulating further efforts on transition metal (TM) based QSH materials.
Transition metal perovskite chalcogenides, a class of materials with rich tunability in functionalities, are gaining increased attention as candidate materials for renewable energy applications. Perovskite oxides are considered excellent n-type thermoelectric materials. Compared to oxide counterparts, we expect the chalcogenides to possess more favorable thermoelectric properties such as lower lattice thermal conductivity and smaller band gap, making them promising material candidates for high temperature thermoelectrics. Thus, it is necessary to study the thermal properties of these materials in detail, especially thermal stability, to evaluate their potential. In this work, we report the synthesis and thermal stability study of five compounds, alpha-SrZrS$_3$, beta-SrZrS$_3$, BaZrS$_3$, Ba$_2$ZrS$_4$, and Ba$_3$Zr$_2$S$_7$. These materials cover several structural types including distorted perovskite, needle-like, and Ruddlesden-Popper phases. Differential scanning calorimeter and thermo-gravimetric analysis measurements were performed up to 1200{deg}C in air. Structural and chemical characterizations such as X-ray diffraction, Raman spectroscopy, and energy dispersive analytical X-ray spectroscopy were performed on all the samples before and after the heat treatment to understand the oxidation process. Our studies show that perovskite chalcogenides possess excellent thermal stability in air at least up to 600{deg}C.
Fabricating complex transition metal oxides with a tuneable band gap without compromising their intriguing physical properties is a longstanding challenge. Here we examine the layered ferroelectric bismuth titanate and demonstrate that, by site-specific substitution with the Mott insulator lanthanum cobaltite, its band gap can be narrowed as much as one electron volt, while remaining strongly ferroelectric. We find that when a specific site in the host material is preferentially substituted, a split-off state responsible for the band gap reduction is created just below the conduction band of bismuth titanate. This provides a route for controlling the band gap in complex oxides for use in emerging oxide opto-electronic and energy applications.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
