Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userTemperature-Dependent Group Delay of Photonic-Bandgap Hollow-Core Fiber Tuned by Surface-Mode Coupling
124
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Surface modes (SM) are highly spatially localized modes existing at the core-cladding interface of photonic-bandgap hollow-core fiber (PBG-HCF). When coupling with SM, the air modes (AM) in the core would suffer a higher loss despite being spectrally within the cladding photonic bandgap, and would be highly dispersive around the avoided crossing (anti-crossing) wavelength. In this paper, we numerically demonstrate that such avoided crossings can play an important role in the tuning of the temperature dependence of group delay of AM of PBG-HCF. At higher temperatures, both the thermal-optic effect and thermal expansion contribute to the redshift of avoided crossing wavelength, giving rise to a temperature dependence of the AM dispersion. Numerical simulations show that the redshift of avoided crossing can significantly tune the thermal coefficient of delay (TCD) of PBG-HCF from -400 ps/km/K to 400 ps/km/K, approximately -120 ppm/K to 120 ppm/K. In comparison with the known tuning mechanism by the thermal-induced redshift of photonic bandgap [Fokoua et al., Optica 4, 659, 2017], the tuning of TCD by SM coupling presents a much broader tuning range and higher efficiency. Our finding would provide a new route to design PBG-HCF for propagation time sensitive applications.
rate research
Read More
We show that two-photon absorption (TPA) in Rubidium atoms can be greatly enhanced by the use of a hollow-core photonic bandgap fiber. We investigate off-resonant, degenerate Doppler-free TPA on the 5S1/2 - 5D5/2 transition and observe 1% absorption of a pump beam with a total power of only 1 mW in the fiber. These results are verified by measuring the amount of emitted blue fluorescence and are consistent with the theoretical predictions which indicate that transit time effects play an important role in determining the two-photon absorption cross-section in a confined geometry.
In this letter, an energetic and highly efficient dispersive wave (DW) generation at 200 nm has been numerically demonstrated by selectively exciting LP$_{02}$-like mode in a 10 bar Ar-filled hollow-core anti-resonant fiber pumping in the anomalous dispersion regime at 1030 nm with pulses of 30 fs duration and 7 $mu$J energy. Our calculations indicate high conversion efficiency of $>$35% (2.5 $mu$J) after propagating 3.6 cm fiber length which is due to the strong shock effect and plasma induced blue-shifted soliton. It is observed that the efficiency of fundamental LP$_{01}$-mode is about 15% which is much smaller than LP$_{02}$-like mode and also emitted at longer wavelength of 270 nm.
We report a series of experimental, analytical and numerical studies demonstrating strong circular dichroism in helically twisted hollow-core single-ring photonic crystal fiber (SR-PCF), formed by spinning the preform during fiber drawing. In the SR-PCFs studied, the hollow core is surrounded by a single ring of non-touching capillaries. Coupling between these capillaries results in the formation of helical Bloch modes carrying orbital angular momentum. In the twisted fiber, strong circular birefringence appears in the ring, so that when a core mode with a certain circular polarization state (say LC) phase-matches to the ring, the other (RC) is strongly dephased. If in addition the orbital angular momentum is the same in core and ring, and the polarization states are non-orthogonal (e.g., slightly elliptical), the LC core mode will experience high loss while the RC mode is efficiently transmitted. The result is a single-circular-polarization SR-PCF that acts as a circular polarizer over a certain wavelength range. Such fibers have many potential applications, for example, for generating circularly polarized light in gas-filled SR-PCF and realizing polarizing elements in the deep and vacuum ultraviolet.
Optimum suppression of higher order modes in single-ring hollow-core photonic crystal fibers (SR-PCFs) occurs when the capillary-to-core diameter ratio d/D = 0.68. Here we report that, in SR-PCFs with sub-optimal values of d/D, higher-order mode suppression can be recovered by spinning the preform during fiber drawing, thus introducing a continuous helical twist. This geometrically increases the effective axial propagation constant (initially too low) of the LP01-like modes of the capillaries surrounding the core, enabling robust single-mode operation. The effect is explored by means of extensive numerical modeling, an analytical model and a series of experiments. Prism-assisted side-coupling is used to investigate the losses and near-field patterns of individual fiber modes in both the straight and twisted cases. More than 12 dB/m improvement in higher order mode suppression is achieved experimentally in a twisted PCF. The measurements also show that the higher order mode profiles change with twist rate, as predicted by numerical simulations. Helical twisting offers an additional tool for achieving effectively endlessly single-mode operation in hollow-core SR-PCFs.
Flying particle sensors in hollow-core photonic crystal fibers require accurate localization of the optically trapped microparticles. We report position measurement to micrometer-resolution, using optical frequency domain reflectometry, of two 1.65-$mu$m-diameter polystyrene particles.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
