Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userPlasma engineering of microstructured piezo and triboelectric hybrid nanogenerators for wide bandwidth vibration energy harvesting
158
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We introduce herein the advanced application of low pressure plasma procedures for the development of piezo and triboelectric mode I hybrid nanogenerators. Thus, plasma assisted deposition and functionalization methods are presented as key enabling technologies for the nanoscale design of ZnO polycrystalline shells, the formation of conducting metallic cores in core@shell nanowires, and for the solventless surface modification of polymeric coatings and matrixes. We show how the perfluorinated chains grafting of PDMS provides a reliable approach to increase the hydrophobicity and surface charges at the same time that keeping the PDMS mechanical properties. In this way, we produce efficient Ag/ZnO convoluted piezoelectric nanogenerators supported on flexible substrates and embedded in PDMS compatible with a contact separation triboelectric architecture. Factors like crystal-line texture, ZnO thickness, nanowires aspect ratio, and surface chemical modification of the PDMS are explored to optimize the power output of the nanogenerators aimed for harvesting from low-frequency vibrations. Just by manual trigger-ing, the hybrid device can charge a microcapacitor to switch on an array of color LEDs. Outstandingly, this simple three-layer architecture allows for harvesting vibration energy in a wide bandwidth, thus, we show the performance characteristics for frequencies between 1 Hz to 50 Hz and demonstrate the successful activation of the system up to ca. 800 Hz
rate research
Read More
Harvesting all sources of available clean energy is an essential strategy to contribute to healing current dependence on non-sustainable energy sources. Recently, triboelectric nanogenerators (TENGs) have gained visibility as new mechanical energy harvester offering a valid alternative to batteries, being particularly suitable for portable devices. Here, the increased capacitance of a few-layer graphene-based electrode is obtained by incorporating nitrogen-doped graphene (N_graphene), enabling a 3_fold enhancement in TENGs power output. The dependence of TENGs performance on the electronic properties of different N_graphene types, varying in the doping concentration and in the relative content of N-pyridinic and N-graphitic sites is investigated. These sites have different electron affinities, and synergistically contribute to the variation of the capacitive and resistive properties of N-graphene and consequently, TENG performance. It is demonstrated that the power enhancement of the TENG occurs when the N_graphene, an n-semiconductor, is interfaced between the positive triboelectric material and the electrode, while a deterioration of the electrical performance is observed when it is placed at the interface with the negative triboelectric material. This behavior is explained in terms of the dependence of N_graphene quantum capacitance on the electrode chemical potential which shifts according to the opposite polarization induced at the two electrodes upon triboelectrification.
We report the design, elaboration and measurements of an innovative planar thermoelectric (TE) devices made of a large array of small mechanically suspended nanogenerators (nanoTEG). The miniaturized TE generators based on SiN membranes are arranged in series and/or in parallel depending on the expected final resistance adapted to the one of the load. The microstructuration allows, at the same time, a high thermal insulation of the membrane from the silicon frame and high thermal coupling to its environment (surrounding air, radiations). We show a ratio of 60% between the measured effective temperature of the membrane, (and hence of the TE junctions), and the available temperature of the heat source (air). The thermal gradient generated across the TE junction reaches a value as high as 60 kelvin per mm. Energy harvesting with this planar TE module is demonstrated through the collected voltage on the TE junctions when a temperature gradient is applied, showing a harvested power on the order of 0.3 $mu$Watt for a 1 cm 2 chip for an effective temperature gradient of 10 K. The optimization of nanoTEGs performances will increase the power harvested significantly and permit to send a signal by a regular communication protocol and feed basic functions like temperature measurement or airflow sensing.
Optical properties of core-shell-shell Au@SiO2@Au nanostructures and their solar energy harvesting applications are theoretically investigated using Mie theory and heat transfer equations. The theoretical analysis associated with size-dependent modification of the bulk gold dielectric function agrees well with previous experimental results. We use the appropriate absorption cross-section to determine the solar energy absorption efficiency of the nano-heterostructures, which is strongly structure-dependent, and to predict the time-dependent temperature increase of the nanoshell solution under simulated solar irradiation. Comparisons to prior temperature measurements and theoretical evaluation of the solar power conversion efficiency are discussed to provide new insights into underlying mechanisms. Our approach would accelerate materials and structure testing in solar energy harvesting.
The thin film configuration presents obvious practical advantages over the 1D implementation in energy harvesting systems such as easily manufacturing and processing and long lasting and stable devices. However, most of the ZnO-based piezoelectric nanogenerators (PENGs) reported so far relay in the exploitation of single-crystalline ZnO nanowires because their self-orientation in the c-axis and ability to accommodate long deformations resulting in a high piezoelectric performance. Herein, we show an innovative approach aiming to produce PENGs by combining polycrystalline ZnO layers fabricated at room temperature by plasma assisted deposition with supported small-molecule organic nanowires (ONWs) acting as 1D scaffold. The resulting hybrid nanostructure is formed by a single-crystalline organic nanowire conformally surrounded by a three dimensional (3D) ZnO shell that combines the mechanical properties of the organic core with the piezoelectric response of the ZnO layer. In a loop forward towards the integration of multiple functions within a single wire, we have also developed ONW@Au@ZnO nanowires including a gold shell acting as inner nanoscopic electrode. Thus, we have built and compare thin films and 3D core@shell ONW@ZnO and ONW@Au@ZnO PENGs showing output piezo-voltages up to 170 mV. The synergistic combination of functionalities in the ONW@Au@ZnO devices promotes an enhanced performance generating piezo-currents almost twenty times larger than the ONW@ZnO nanowires and superior to the thin film nanogenerators for equivalent and higher thicknesses.
The performance of ultra-wide band gap materials like $beta$-Ga$_mathrm{2}$O$_mathrm{3}$ is critically dependent on achieving high average electric fields within the active region of the device. In this report, we show that high-k gate dielectrics like BaTiO$_mathrm{3}$ can provide an efficient field management strategy by improving the uniformity of electric field profile in the gate-drain region of lateral field effect transistors. Using this strategy, we were able to achieve high average breakdown fields of 1.5 MV/cm and 4 MV/cm at gate-drain spacing (L$_mathrm{gd}$) of 6 um and 0.6 um respectively in $beta$-Ga$_mathrm{2}$O$_mathrm{3}$, at a high channel sheet charge density of 1.8x10$^mathrm{13}$cm$^mathrm{-2}$. The high sheet charge density together with high breakdown field enabled a record power figure of merit (V$^mathrm{2}$$_mathrm{br}$/R$_mathrm{on}$) of 376 MW/cm$^mathrm{2}$ at a gate-drain spacing of 3 um.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
