Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDeformation Behaviour of Ion-Irradiated FeCr: A Nanoindentation Study
75
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Understanding the mechanisms of plasticity in structural steels is essential for the operation of next-generation fusion reactors. Elemental composition, particularly the amount of Cr present, and irradiation can have separate and synergistic effects on the mechanical properties of ferritic/martensitic steels. The study of ion-irradiated FeCr alloys is useful for gaining a mechanistic understanding of irradiation damage in steels. Previous studies of ion-irradiated FeCr did not clearly distinguish between the nucleation of dislocations to initiate plasticity, and their propagation through the material as plasticity progresses. In this study, Fe3Cr, Fe5Cr, and Fe10Cr were irradiated with 20 MeV Fe$^{3+}$ ions at room temperature to nominal doses of 0.01 dpa and 0.1 dpa. Nanoindentation was carried out with Berkovich and spherical indenter tips to study the nucleation of dislocations and their subsequent propagation. The presence of irradiation-induced defects reduced the theoretical shear stress and barrier for dislocation nucleation. The presence of Cr further enhanced this effect due to increased retention of irradiation defects. However, this combined effect is still small compared to dislocation nucleation from pre-existing sources such as Frank-Read sources and grain boundaries. The yield strength, an indicator of dislocation mobility, of FeCr increased with irradiation damage and Cr. The increased retention of irradiation defects due to the presence of Cr also further increased the yield strength. Reduced work hardening capacity was also observed following irradiation. The synergistic effects of Cr and irradiation damage in FeCr appear to be more important for the propagation of dislocations, rather than their nucleation.
rate research
Read More
Ion-irradiated FeCr alloys are useful for understanding and predicting neutron-damage in the structural steels of future nuclear reactors. Previous studies have largely focused on the structure of irradiation-induced defects, probed by transmission electron microscopy (TEM), as well as changes in mechanical properties. Across these studies, a wide range of irradiation conditions has been employed on samples with different processing histories, which complicates the analysis of the relationship between defect structures and material properties. Furthermore, key properties, such as irradiation-induced changes in thermal transport and lattice strain, are little explored. Here we present a systematic study of Fe3Cr, Fe5Cr and Fe10Cr binary alloys implanted with 20 MeV Fe$^{3+}$ ions to nominal doses of 0.01 dpa and 0.1 dpa at room temperature. Nanoindentation, transient grating spectroscopy (TGS) and X-ray micro-beam Laue diffraction were used to study the changes in hardness, thermal diffusivity and strain in the material as a function of damage and Cr content. Our results suggest that Cr leads to an increased retention of irradiation-induced defects, causing substantial changes in hardness and lattice strain. However, thermal diffusivity varies little with increasing damage and instead degrades significantly with increasing Cr content in the material. We find significant lattice strains even in samples exposed to a nominal displacement damage of 0.01 dpa. The defect density predicted from the lattice strain measurements is significantly higher than that observed in previous TEM studies, suggesting that TEM may not fully capture the irradiation-induced defect population.
Predicting the dramatic changes in material properties caused by irradiation damage is key for the design of future nuclear fission and fusion reactors. Self-ion implantation is an attractive tool for mimicking the effects of neutron irradiation. However, the damaged layer of implanted samples is only few microns thick, making it difficult to estimate macroscopic properties. Here we address this challenge using a combination of experimental and modelling techniques. We concentrate on self-ion-implanted tungsten, the front-runner for fusion armour components and a prototypical bcc material. To capture dose-dependent evolution of properties, we experimentally characterise samples with damage levels from 0.01 to 1 dpa. Spherical nano-indentation of <001> grains shows hardness increasing up to a dose of 0.032 dpa, beyond which it saturates. AFM measurements show pile-up increasing up to the same dose, beyond which large pile-up and slip-steps are seen. Based on the observations we develop a crystal plasticity (CPFE) model for the irradiated material. It captures irradiation-induced hardening followed by strain-softening through interaction of irradiation-defects and gliding dislocations. Shear resistance of irradiation-defects is derived from TEM observations of similarly irradiated samples. Nano-indentation of pristine and implanted tungsten of doses 0.01, 0.1, 0.32 and 1 dpa is simulated. Two model parameters are fitted to the experimental results of the 0.01 dpa sample and are kept unchanged for all other doses. Peak load, indent surface profiles and damage saturation predicted by the CPFE model closely match experimental observations. Predicted lattice distortions and dislocation distributions around indents agree with corresponding measurements from HR-EBSD. Finally, the CPFE model is used to predict the macroscopic stress-strain response of similarly irradiated bulk tungsten material.
Formation energy of the $sigma$-phase in the Fe-Cr alloy system, $Delta E$, was computed versus the occupancy changes on each of the five possible lattice sites. Its dependence on a number of Fe-atoms per unit cell, $N_{Fe}$, was either monotonically increasing or decreasing function of $N_{Fe}$, depending on the site on which Fe-occupancy was changed. Based on the calculated $Delta E$ - values, the average formation energy, $<Delta E>$, was determined as a weighted over probabilities of different atomic configurations. The latter has a minimum in the concentration range where the $sigma$-phase exists. The minimum in that range of composition was also found for the free energy calculated for 2000 K and taking only the configurational entropy into account.
A decrease of fracture toughness of irradiated materials is usually observed, as reported for austenitic stainless steels in Light Water Reactors (LWRs) or copper alloys for fusion applications. For a wide range of applications (e.g. structural steels irradiated at low homologous temperature), void growth and coalescence fracture mechanism has been shown to be still predominant. As a consequence, a comprehensive study of the effects of irradiation-induced hardening mechanisms on void growth and coalescence in irradiated materials is required. The effects of irradiation on ductile fracture mechanisms - void growth to coalescence - are assessed in this study based on model experiments. Pure copper thin tensile samples have been irradiated with protons up to 0.01 dpa. Micron-scale holes drilled through the thickness of these samples subjected to uniaxial loading conditions allow a detailed description of void growth and coalescence. In this study, experimental data show that physical mechanisms of micron-scale void growth and coalescence are similar between the unirradiated and irradiated copper. However, an acceleration of void growth is observed in the later case, resulting in earlier coalescence, which is consistent with the decrease of fracture toughness reported in irradiated materials. These results are qualitatively reproduced with numerical simulations accounting for irradiation macroscopic hardening and decrease of strain-hardening capability.
Understanding defect production and evolution under irradiation is a long-standing multi-scale problem. Conventionally, experimental examination of irradiation-induced defects (IIDs) has mainly relied on transmission electron microscopy (TEM), which offers high spatial resolution but requires destructive sample preparation. Furthermore, limited field of view and low strain sensitivity make multi-scale characterisation and quantitative strain measurements difficult. Here we explore the potential of using advanced techniques in the scanning electron microscope (SEM) to non-destructively probe irradiation damage at the surface of bulk materials. Electron channelling contrast imaging (ECCI) is used to image nano-scale irradiation-induced defects in 20 MeV self-ion irradiated tungsten, the main candidate material for fusion reactor armour. The results show an evolution of the damage microstructure from uniformly and randomly distributed nano-scale defects at 0.01 dpa (displacement per atom) to string structures extending over hundreds of nanometres at 1 dpa. Cross-correlation based high-resolution EBSD (HR-EBSD) is used to probe the lattice strain fields associated with IIDs. While there is little strain fluctuation at 0.01 dpa, significant heterogeneity in the lattice strains is observed at 0.1 dpa, increasing with dose until saturation at 0.32 dpa. The characteristic length scale of strain fluctuations is ~500 nm. Together, ECCI and HR-EBSD reveal a transition from a structure where defects are disordered to a structure with long-range order driven by elastic interactions between pre-existing defects and new cascade damage. This study demonstrates that SEM provides an attractive tool for rapid throughput, non-destructive, multi-scale and multi-aspect characterisation of irradiation damage.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
