Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userFirst-principles study of defects at $Sigma3$ grain boundaries in CuGaSe$_2$
102
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We present a first-principles computational study of cation-Se $Sigma$3 (112) grain boundaries in CuGaSe$_2$. We discuss the structure of these grain boundaries, as well as the effect of native defects and Na impurities on their electronic properties. The formation energies show that the defects will tend to form preferentially at the grain boundaries, rather than in the grain interiors. We find that in Ga-rich growth conditions Cu vacancies as well as Ga at Cu and Cu at Ga antisites are mainly responsible for having the equilibrium Fermi level pinned toward the middle of the gap, resulting in carrier depletion. The Na at Cu impurity in its +1 charge state contributes to this. In Ga-poor growth conditions, on the other hand, the formation energies of Cu vacancies and Ga at Cu antisites are comparatively too high for any significant influence on carrier density or on the equilibrium Fermi level position. Thus, under these conditions, the Cu at Ga antisites give rise to a $p$-type grain boundary. Also, their formation energy is lower than the formation energy of Na at Cu impurities. Thus, the latter will fail to act as a hole barrier preventing recombination at the grain boundary, in contrast to what occurs in CuInSe$_2$ grain boundaries. We also discuss the effect of the defects on the electronic properties of bulk CuGaSe$_2$, which we assume reflect the properties of the grain interiors.
rate research
Read More
Oxygen vacancies have been identified to play an important role in accelerating grain growth in polycrystalline perovskite-oxide ceramics. In order to advance the fundamental understanding of growth mechanisms at the atomic scale, classical atomistic simulations were carried out to investigate the atomistic structures and oxygen vacancy formation energies at grain boundaries in the prototypical perovskite-oxide material SrTiO$_3$. In this work, we focus on two symmetric tilt grain boundaries, namely $Sigma$5(310)[001] and $Sigma$5(210)[001]. A one-dimensional continuum model is adapted to determine the electrostatic potential induced by charged lattice planes in atomistic structure models containing grain boundaries and point defects. By means of this model, electrostatic artifacts, which are inherent to supercell models with periodic or open boundary conditions, can be taken into account and corrected properly. We report calculated formation energies of oxygen vacancies on all the oxygen sites across boundaries between two misoriented grains, and we analyze and discuss the formation-energy values with respect to local charge densities at the vacant sites.
The structural, electronic, and adhesive properties of Cu/SiO$_2$ interfaces are investigated using first-principles density-functional theory within the local density approximation. Interfaces between fcc Cu and $alpha$-cristobalite(001) surfaces with different surface stoichiometries are considered. Interfacial properties are found to be sensitive to the choice of the termination, and the oxygen density at the substrate surface is the most important factor influencing the strength of adhesion. For oxygen-rich interfaces, the O atoms at the interface substantially rearrange after the deposition of Cu layers, suggesting the formation of Cu-O bonds. Significant hybridization between Cu$-d$ and O$-p$ states is evident in site-projected density of states at the interface. As oxygen is systematically removed from the interface, less rearrangement is observed, implying weaker adhesion. Computed adhesion energies for each of the interfaces are found to reflect these observed structural and bonding trends, leading to the largest adhesion energy in the oxygen rich cases. The adhesion energy is also calculated between Cu and SiO$_2$ substrates terminated with hydroxyl groups, and adhesion of Cu to these substrates is found to be considerably reduced. This work supports the notion that Cu films can adhere well to hydroxyl-free SiO$_2$ substrates should oxygen be present in sufficient amounts at the interface.
The strong spin-spin exchange interaction in some low-dimensional magnetic materials can give rise to a high group velocity and thermal conductivity contribution from magnons. One example is the incommensurate layered compounds (Sr,Ca,La)14Cu24O41. The effects of grain boundaries and defects on quasi-one-dimensional magnon transport in these compounds are not well understood. Here we report the microstructures and anisotropic thermal transport properties of textured Sr14Cu24O41, which are prepared by solid-state reaction followed by spark plasma sintering. Transmission electron microscopy clearly reveals nano-layered grains and the presence of dislocations and planar defects. The thermal conductivity contribution and mean free paths of magnons in the textured samples are evaluated with the use of a kinetic model for one-dimensional magnon transport, and found to be suppressed significantly as compared to single crystals at low temperatures. The experimental results can be explained by a one-dimensional magnon-defect scattering model, provided that the magnon-grain boundary scattering mean free path in the anisotropic magnetic structure is smaller than the average length of these nano-layers along the c axis. The finding suggests low transmission coefficients for magnons across grain boundaries.
Transparent oxide materials, such as $CuAlO_{2}$, a p-type transparent conducting oxide (TCO), have recently been studied for high temperature thermoelectric power generators and coolers for waste heat. TCO materials are generally low cost and non-toxic. The potential to engineer them through strain and nano-structuring are two promising avenues toward continuously tuning the electronic and thermal properties to achieve high zT values and low cost/kW-hr devices. In this work, the strain-dependent lattice thermal conductivity of 2H $CuAlO_{2}$ is computed by solving the phonon Boltzmann transport equation with interatomic force constants extracted from first-principles calculations. While the average bulk thermal conductivity is around 32 W/(K-m) at room temperature, it drops to between 5-15 W/(K-m) for typical experimental grain sizes from 3nm to 30nm at room temperature. We find that strain can offer both an increase as well as a decrease in the thermal conductivity as expected, however the overall inclusion of small grain sizes dictates the potential for low thermal conductivity in this material.
Flexoelectricity is a type of ubiquitous and prominent electromechanical coupling, pertaining to the response of electrical polarization to mechanical strain gradients while not restricted to the symmetry of materials. However, large elastic deformation in most solids is usually difficult to achieve and the strain gradient at minuscule is challenging to control. Here we exploit the exotic structural inhomogeneity of grain boundary to achieve a huge strain gradient (~ 1.2 nm-1) within 3 ~ 4 unit-cells, and thus obtain atomic-scale flexoelectric polarization up to ~ 38 {mu}C/cm2 at a 24 LaAlO3 grain boundary. The nanoscale flexoelectricity also modifies the electrical activity of grain boundaries. Moreover, we prove that it is a general and feasible way to form large strain gradients at atomic scale by altering the misorientation angles of grain boundaries in different dielectric materials. Thus, engineering of grain boundaries provides an effective pathway to achieve tunable flexoelectricity and broadens the electromechanical functionalities of non-piezoelectric materials.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
